Abstract:The effect of nitrogen content on the formation of an equiaxed solidification structure of Fe-16Cr steel was investigated. Moreover, two different kinds of refractory materials, i.e., alumina and magnesia, were employed to control the type of oxide inclusion. The characteristics of TiN(-oxide) inclusions were quantitatively analyzed in both molten steel and solidified samples. When the melting was carried out in the alumina refractory, the grain size continuously decreased with increasing nitrogen content. However, a minimum grain size was observed at a specific nitrogen content (approx. 150 ppm) when the steel was melted in the magnesia refractory. Most of the single TiN particles had a cuboidal shape and fine irregularly shaped particles were located along the grain boundary due to the microsegregation of Ti at the grain boundary during solidification. The type of TiN-oxide hybrid inclusion was strongly affected by the refractory material where Al2O3-TiN and MgAl2O4-TiN hybrid-type inclusions were obtained in the alumina and magnesia refractory experiments, respectively. The formation of oxide inclusions was well predicted by thermochemical computations and it was commonly found that oxide particles were initially formed, followed by the nucleation and growth of TiN. When the nitrogen content increased, the number density of TiN linearly increased in the alumina refractory experiments. However, the number of TiN exhibits a maximum at about [N] = 150 ppm, at which a minimum grain size was obtained in the magnesia refractory experiments. Therefore, the larger the number density of TiN, the smaller the primary grain size after solidification. The number density of TiN in the steel melted in the magnesia refractory was greater than that in the steel melted in the alumina refractory at given Ti and N contents, which was due to the lower planar lattice disregistry of MgAl2O4-TiN interface rather than that of Al2O3-TiN interface. When ∆TTiN (= difference between the TiN precipitation temperature and the liquidus of the steel) was 20 K to 40 K, the number density of effective TiN was maximized and thus, the grain size was minimized after solidification. Finally, although most of the TiN particles were smaller than 1 μm in the molten steel samples irrespective of the nitrogen content, TiN particles larger than 10 μm were observed in the solidified samples when the nitrogen content was greater than 150 ppm. The growth of TiN particles during melting and solidification was well predicted by the combinatorial simulation of the ‘Ostwald ripening model’ based on the Lifshitz–Slyozov–Wagner theory in conjunction with the ‘Diffusion controlled model’ using Ohnaka’s microsegregation equation.

Effect of Non-metallic Inclusions in Fe-Al-Ti-O-N-S Alloy on Grain Size

Effects of aluminum and titanium additions on the formation of nonmetallic inclusions in nickel-based superalloys

Synergistic Effect of Nitrogen and Refractory Material on TiN Formation and Equiaxed Grain Structure of Ferritic Stainless Steel

Effect of Micro-Alloyed Ti on Inclusions Modification

Ferrite Formation Dynamics and Microstructure Due to Inclusion Engineering in Low-Alloy Steels by Ti2O3 and TiN Addition

The Effect of Heat Treatments on the Microstructural Evolution of Twin-Roll-Cast Al-Fe-Si Alloys

Evolution Behavior of TiN Inclusions in Austenitic Fe-36Ni Alloy during Heating at 1473 and 1673 K

Effect of Magnesium Content on Precipitation Behavior of TiN-Containing Inclusions in High-Titanium High-Strength Steel

Effect of LCFeCr Alloy Additions on the Non-metallic Inclusion Characteristics in Ti-Containing Ferritic Stainless Steel

Effect of oxygen content on composition of inclusion precipitated during solidification of steel

Effect of Al Content on Inclusions in Fe‐15Mn‐xAl‐C Low‐Density Steel

Effect of Cooling Rate on Superfine Ti-O Inclusion Precipitation During Directional Solidification

Inclusion and Microstructure Characteristics in Steels with TiN Additions

Effect of Niobium on Inclusions in Fe-Mn-C-Al Twinning-Induced Plasticity Steel

Effect of Mg–Ti Treatment on Nucleation Mechanism of TiN Inclusions and Ferrite

Evolution of the Non-metallic Inclusions Influenced by Slag-Metal Reactions in Ti-Containing Ferritic Stainless Steel

Evolution of Inclusions and Associated Microstructure in Ti–Mg Oxide Metallurgy Steel

Transient Behavior and Thermodynamics of Inclusions in Al-Ti-Deoxidized and Ca-Treated Steel

Experimental Study and Thermodynamic Analysis of Inclusion Precipitation During Solidification in 12% Cr Alloy

Agglomeration Behaviors of Different Types of Complex TiN Inclusions in High Titanium Wear Resistant Steel

Effect of Ti Addition on Non‐Metallic Inclusion Characteristics in TRIP Steel