Abstract:NiO nanomaterials prepared using a solid–liquid NH3·H2O precipitation method (NiO-NSL) were tested in the catalytic combustion of methane. The NiO-NSL presented a characteristic rod-like nanostructure with a length of about a few hundred nanometers except for a part of the nanoparticles. For comparison, the NiO nanomaterials prepared by the traditional liquid-phase NH3·H2O precipitation method (NiO-NLL) were tested in the same reaction conditions. NiO-NSL exhibited significantly higher methane combustion activity than NiO-NLL and achieved the complete combustion of methane at 390 °C, which was outstanding in non-noble metal-based catalyst. X-ray photoelectron spectroscopy (XPS) and hydrogen-temperature-programmed reduction (H2-TPR) results indicate that the surface Ni2+ content of NiO-NSL was higher than that of NiO-NLL, and the presence of more Ni2+ might be responsible for the enhanced activity. DFT calculations prove that the energy barrier for C–H bond activation on Ni2+ was lower than that on Ni3+, which was consistent with the higher methane catalytic combustion activity of NiO-NSL. In addition, when the precipitating agent was replaced with NaOH and (NH4)2CO3, the generalization of the solid–liquid precipitation method in the preparation of the NiO catalysts was also tested. The results show that the solid–liquid precipitation method proposed in this work was still applicable when NaOH was used as a precipitant. However, with the use of (NH4)2CO3 as a precipitant, the methane catalytic activity of the NiO nanoparticles prepared by the solid–liquid precipitation method was reduced to a certain extent compared with the traditional liquid-phase precipitation method. This research can open up a highly efficient and environmentally friendly method for the synthesis of methane combustion catalysts.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsanm.1c00732?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsanm.1c00732</a>.Stability test results of NiO-NSL (Figure S1); wide-angle XRD patterns of the as-precipitated samples using (NH4)2CO3 as the precipitant and a standard xNiCO3·yNi(OH)2 sample (Figure S2); representative TEM images of the precursors and as-calcined catalysts of the other four samples (Figures S3 and S4); specific performance data of samples in previous research (Table S1); XPS analysis of the other samples (Table S2, Figures S5 and S6); H2-TPR profiles of the other samples (Table S3, Figures S7 and S8); detailed DFT calculation results (Table S4); the surface model used in the calculations (Figure S9) (<a class="ext-link" href="/doi/suppl/10.1021/acsanm.1c00732/suppl_file/an1c00732_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Part I: NiMoO4 Nanostructures Synthesized by the Solution Combustion Method: A Parametric Study on the Influence of Synthesis Parameters on the Materials’ Physicochemical, Structural, and Morphological Properties

PREPARATION OF NiO NANOPARTICLES ON THE SILICA SURFACE BY ADSORPTION PHASE SYNTHESIS AND ITS REGULATION ON MORPHOLOGY OF NiO PARTICLES

Influence of Various Parameters on the SCS Ni/NiO Nanostructures and their Mechanism of Formation

Nanomaterials Via Solution Combustion Synthesis: a Step Nearer to Controllability

Part II: NiMoO4 Nanostructures Synthesized by the Solution Combustion Method: A Parametric Study on the Influence of Material Synthesis and Electrode-Fabrication Parameters on the Electrocatalytic Activity in the Hydrogen Evolution Reaction

Mechanism of Auto Combustion Method in Synthesis of Nanocrystalline NiFe<SUB>2</SUB>O<SUB>4</SUB> Powders: Mechanism of Auto Combustion Method in Synthesis of Nanocrystalline NiFe<SUB>2</SUB>O<SUB>4</SUB> Powders

Irregularly Shaped NiO Nanostructures for Catalytic Lean Methane Combustion

Influence of some parameters on the synthesis of nanosized NiO material by modified sol–gel method

Combustion Agent Mediated Flash Synthesis of Porous MCo2O4 (M = Zn, Ni, Cu and Fe) Via Self-Sustained Decomposition of Metal-Organic Complexes

Solution Combustion Synthesis and Kinetic Measurements in Ni(NO3)2–C6H8O7 System. Preparation of Nickel Powder

Structure, Surface Nature, Thermal Stability, and Biomass Gasification Process of NiO/SiO2 and NiO-Pr2O3/SiO2 Nanocomposites Obtained through Facile Deposition Precipitation Method

Preparation of Nanometer NiFe2O4 Powder by Low-temperature Combustion Synthesis Method

Combustion of Aluminum Nanoparticles and Exfoliated 2D Molybdenum Trioxide Composites

Effect of calcination time on NiAl-Al2O3 using gel combustion synthesis method

Effect of Fuel-to-oxidizer Ratios on Combustion Mode and Microstructure of Li2TiO3 Nanoscale Powders

Mechanism of Auto Combustion Method in Synthesis of Nanocrystalline SiFe_2O_4 Powders

Effect of preparation method on the surface properties and activity of Ni0.7Cu0.3Fe2O4 nanoparticles

Optimizing Solution Combustion Method Fuel Ratios for Enhanced Electrochemical Performance of LiNi0.5Mn1.5O4 Cathode Materials

Synthesis and characterization of Mn3O4 and Mn2O3 nanocrystals on SBA-15: Novel combustion catalysts at low reaction temperatures

Effect Of Synthesis Method On The Physical And Catalytic Property Of Nanosized Nio

Effects of excess NaClO 4 on phases, size and magnetic properties of Ni–Zn ferrite powders prepared by combustion synthesis