Abstract:Effective thermal management is key to ensuring the reliable operation of high power electronic equipment. In this study, the strategy of phase transition and liquid cooling coupling applied to transient high power electronic equipment has been examined. In order to improve the performance of the phase changing material (PCM) in temperature control, the effects of the coupling structure have been addressed with a consideration of fin, copper foam (CF), graphite foam (GF), fin-copper foam (FCF) and fin-graphite foam (FGF) structures in heat dissipation. In this study, pure paraffin wax (PPW) was used as phase change material to prepare heat sinks based on the above five structures. The experimental study investigates the impact of different thermal conductivity strategies on temperature control characteristics, with a focus on cold capacity recovery and the combined phase change and liquid cooling, using pure paraffin wax module as a reference. The results have revealed that the fin-foam coupling structure delivers a better PCM performance than the single fin or foam structure. Operating at a heating power of 10 W, 15 W and 20 W, the temperature control time of the FGF structure was increased by 13.6 %∼14.6 % relative to the GF structure. At 15 °C with flow rates of 1 L/min, 1.5 L/min, 2 L/min liquid cooling conditions, the cooling capacity recovery time was reduced by 18.8 %, 17.2 %, 19.7 %, respectively. In the phase-change liquid-cooling coupling temperature control experiment, the final temperature increase in the FGF system was 11.7 °C -15.2 °C lower than that of the GF system under the same water temperature and volume flow for a 50 W heat source. The incorporation of fins also enhanced the thermal conductivity strengthening capability of the copper foam and reduced the cold recovery time. Based on the comprehensive evaluation, the FGF structure demonstrates superior temperature control performance and cold recovery characteristics of PCM, making it an optimal strengthening method. Following closely are the FCF, GF, Fin and CF structures. Compared to pure paraffin modules, these five modules exhibit varying degrees of improvement in temperature control and cold capacity recovery efficiency. This study provides guidance for optimizing heat sink design based on PCM in electronic applications.

Experimental investigation of the simultaneous effect of using phase change material/plate-fin heat sink on thermal performance of a power supply unit

Transient Performance of a PCM-based Heat Sink with a Partially Filled Metal Foam: Effects of the Filling Height Ratio

Effects of Melting Temperature and the Presence of Internal Fins on the Performance of a Phase Change Material (Pcm)-Based Heat Sink

An experimental study for thermal management using hybrid heat sinks based on organic phase change material, copper foam and heat pipe

Experimental and numerical investigations on the intermittent heat transfer performance of rectangular cavity plate fin phase change material based heat sink

Thermal performance of phase change material–based heat sink for passive cooling of electronic components: An experimental study

Thermal performance assessment of phase change material for electronic cooling: An experimental investigation

Numerical thermal performance assessment of phase change process in a PCM/foam-fins enclosure under various thermal conditions

Experimental study of heat transfer enhancement using metal foam partially filled with phase change material in a heat sink

Investigation of Phase Change Material Integrated With High Thermal Conductive Carbon Foam Inside Heat Sinks for Thermal Management of Electronic Components

Investigation on the Melting Performance of a Phase Change Material Based on a Shell-and-Tube Thermal Energy Storage Unit with a Rectangular Fin Configuration

Thermal performance of a PCM heat sink under different heat loads: An experimental study

Efficient Thermal Energy Management of Hollow Pin Fin Heat Sinks with and without Phase Change Material

A hybrid thermal management phase change material based pin-fin heat sinks under forced convection

Influence of the foam-fin structure on the thermal performance of a coupled phase change liquid cooling module

Thermal Performance of a Phase Change Material-Based Heat Sink Subject to Constant and Power Surge Heat Loads: A Numerical Study

A novel personal cooling system (PCS) incorporated with phase change materials (PCMs) and ventilation fans: An investigation on its cooling efficiency

Thermal Performance of Heat Sink Filled with Double-Porosity Porous Aluminum Skeleton/Paraffin Phase Change Material

Impact of using different numbers of fins on heat transfer augmentation in a phase-change material helical coil latent energy storage system

Numerical simulation of thermal performance of heat sink augmented with phase change material PCM integrated with solid and aluminum metal foam fins

Investigation of enhanced PCM heat sink design under extreme thermal conditions for high-heat-generating electronic devices