Abstract:Despite the rapid progress that has been made in increasing the power conversion efficiency (PCE) of organic solar cells (OSCs) over the past decade, it is a challenge to realize efficient and environment-friendly OSCs. In this contribution, all polymer solar cells were fabricated with a blend of poly[4,8-bis(5-(2-ethylhexyl) thiophen-2-yl) benzo[1,2-b: 4,5-b'] dithiophene-co-3-fluorothieno[3,4-b] thiophene-2-carboxylate] (PTB7Th) donor and vinylene-bridged perylenediimide-based polymer (PDI-V) acceptor, in which non-halogenated tetrahydrofuran (THF) was used as the host solvent. A conventional device structure of ITO/poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS)/PTB7-Th:PDI-V/zirconium acetylacetonate (ZrAcac)/Al was employed, where PEDOT:PSS functioned as the hole transporting layer (HTL) and ZrAcac functioned as the electron transporting layer (ETL). The mixed solution of PTB7-Th and PDI-V was spin cast on the top of PEDOT:PSS layer to form the active layer. After that, ZrAcac solution was spin cast on the top of PTB7-Th:PDI-V layer. Different thermal annealing temperatures were used to optimize the active layer morphology. In details, OSCs without thermal annealing showed a PCE of 7.1%, with a short-circuit current (J(SC)) of 14.9 mA/cm(2), an open-circuit voltage (V-OC) of 0.74 V, and a fill factor (FF) of 64%. The devices annealed at 120 degrees C showed a high PCE of 8.1% with a J(SC) of 15.5 mA/cm(2), a V-OC of 0.74 V, and a FF of 70%. Further increasing the annealing temperature to 150 degrees C led to decreased FF and thereby a relatively lower PCE (7.4%). To the best of our knowledge, the PCE of similar to 8.1% is one of the highest PCE values reported in the literature so far for all polymer solar cells. The high and balanced hole and electron mobility partially contributed to such a high performance. These results suggest that THF as good non-halogenated solvent can be used to fabricate high-performance all polymer solar cells. Higher efficiency can be achieved for OSCs with THF solvent when better polymer acceptors are employed.

High-efficiency and air-stable P3HT-based polymer solar cells with a new non-fullerene acceptor

High‐Efficiency P3HT‐Based All‐Polymer Solar Cells with a Thermodynamically Miscible Polymer Acceptor

A Universal Nonhalogenated Polymer Donor for High‐Performance Organic Photovoltaic Cells

High-performance All Polymer Solar Cells Fabricated with Non-halogenated Solvent

A Non-Conjugated Polymer Acceptor for Efficient and Thermally Stable All-Polymer Solar Cells

A High-Performance Organic Photovoltaic System with Versatile Solution Processability

A Non-Fullerene Acceptor Enables Efficient P3HT-based Organic Solar Cells with Small Voltage Loss and Thickness Insensitivity

Over 14% efficiency all-polymer solar cells enabled by a low bandgap polymer acceptor with low energy loss and efficient charge separation

Novel wide-bandgap non-fullerene acceptors for efficient tandem organic solar cells

Efficient All-Polymer Solar Cells Based on a New Polymer Acceptor Achieving 10.3% Power Conversion Efficiency

Novel Cost-Effective Acceptor:P3ht Based Organic Solar Cells Exhibiting The Highest Ever Reported Industrial Readiness Factor

Progress in Poly (3‐hexylthiophene) Organic Solar Cells and the Influence of Its Molecular Weight on Device Performance

Asymmetric Alkyl Chain Engineering for Efficient and Eco‐Friendly Organic Photovoltaic Cells

P3HT-Based Organic Solar Cells with a Photoresponse to 1000 nm Enabled by Narrow Band Gap Nonfullerene Acceptors with High HOMO Levels

Molecular Design of Fully Nonfused Acceptors for Efficient Organic Photovoltaic Cells

Nonhalogen Solvent‐Processed Asymmetric Wide‐Bandgap Polymers for Nonfullerene Organic Solar Cells with over 10% Efficiency

Non-Fullerene Polymer Solar Cells Based On Alkylthio And Fluorine Substituted 2d-Conjugated Polymers Reach 9.5% Efficiency

8.30% Efficiency P3HT-based All-Polymer Solar Cells Enabled by a Miscible Polymer Acceptor with High Energy Levels and Efficient Electron Transport

Toward High Efficiency Organic Photovoltaic Devices With Enhanced Thermal Stability Utilizing P3ht-B-P3pht Block Copolymer Additives

Eco‐Compatible Solvent‐Processed Organic Photovoltaic Cells with Over 16% Efficiency

Air-stable Triarylamine-Based Amorphous Polymer As Donor Material for Bulk-Heterojunction Organic Solar Cells