Abstract:Despite the rapid progress that has been made in increasing the power conversion efficiency (PCE) of organic solar cells (OSCs) over the past decade, it is a challenge to realize efficient and environment-friendly OSCs. In this contribution, all polymer solar cells were fabricated with a blend of poly[4,8-bis(5-(2-ethylhexyl) thiophen-2-yl) benzo[1,2-b: 4,5-b'] dithiophene-co-3-fluorothieno[3,4-b] thiophene-2-carboxylate] (PTB7Th) donor and vinylene-bridged perylenediimide-based polymer (PDI-V) acceptor, in which non-halogenated tetrahydrofuran (THF) was used as the host solvent. A conventional device structure of ITO/poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS)/PTB7-Th:PDI-V/zirconium acetylacetonate (ZrAcac)/Al was employed, where PEDOT:PSS functioned as the hole transporting layer (HTL) and ZrAcac functioned as the electron transporting layer (ETL). The mixed solution of PTB7-Th and PDI-V was spin cast on the top of PEDOT:PSS layer to form the active layer. After that, ZrAcac solution was spin cast on the top of PTB7-Th:PDI-V layer. Different thermal annealing temperatures were used to optimize the active layer morphology. In details, OSCs without thermal annealing showed a PCE of 7.1%, with a short-circuit current (J(SC)) of 14.9 mA/cm(2), an open-circuit voltage (V-OC) of 0.74 V, and a fill factor (FF) of 64%. The devices annealed at 120 degrees C showed a high PCE of 8.1% with a J(SC) of 15.5 mA/cm(2), a V-OC of 0.74 V, and a FF of 70%. Further increasing the annealing temperature to 150 degrees C led to decreased FF and thereby a relatively lower PCE (7.4%). To the best of our knowledge, the PCE of similar to 8.1% is one of the highest PCE values reported in the literature so far for all polymer solar cells. The high and balanced hole and electron mobility partially contributed to such a high performance. These results suggest that THF as good non-halogenated solvent can be used to fabricate high-performance all polymer solar cells. Higher efficiency can be achieved for OSCs with THF solvent when better polymer acceptors are employed.

Novel Cost-Effective Acceptor:P3ht Based Organic Solar Cells Exhibiting The Highest Ever Reported Industrial Readiness Factor

Completely Non‐fused Low‐cost Acceptor Enables Organic Photovoltaic Cells with 17% Efficiency

Dithienopicenocarbazole-Based Acceptors For Efficient Organic Solar Cells With Optoelectronic Response Over 1000 Nm And An Extremely Low Energy Loss

Easily Available High‐Performance Organic Solar Cells by Regulating Phenylalkyl Side Groups of Non‐Fused Ring Electron Acceptors

A Non-Fullerene Acceptor Enables Efficient P3HT-based Organic Solar Cells with Small Voltage Loss and Thickness Insensitivity

High-efficiency and air-stable P3HT-based polymer solar cells with a new non-fullerene acceptor

Pyran-fused non-fullerene acceptor achieving 15.51% efficiency in organic solar cells

Suppressed non-radiative loss and efficient hole transfer at a small highest occupied molecular orbital offset endows binary organic solar cells with 19.73% efficiency and a small efficiency-cost gap

Fully Non‐Fused Ring Electron Acceptors Enable Effective Additive‐Free Organic Solar Cells with Enhanced Exciton Diffusion Length

Ternary solvent-processed efficient organic solar cells based on a new A-DA′D-A acceptor derivative employing the 3rd-position branching side chains on pyrroles

High‐Efficiency Organic Solar Cells with Wide Toleration of Active Layer Thickness

Over 13% Efficient Organic Solar Cells Based on Low‐Cost Pentacyclic A‐DA′D‐A‐Type Nonfullerene Acceptor

Enhanced Crystal Network and Charge Transfer of Non-Fused Ring Electron Acceptor Via Interchain Interaction Enable Efficient and Stable Organic Solar Cells

Asymmetric simple unfused acceptor enabling over 12% efficiency organic solar cells

High‐Efficiency P3HT‐Based All‐Polymer Solar Cells with a Thermodynamically Miscible Polymer Acceptor

High-performance All Polymer Solar Cells Fabricated with Non-halogenated Solvent

Terthiophene based low-cost fully non-fused electron acceptors for high-efficiency as-cast organic solar cells

Enhanced crystal network and charge transfer of non-fused ring electron acceptors via interchain interaction for efficient and stable organic solar cells

High performance and low cost organic solar cells based on pentacyclic A-DA'D-A acceptor with efficiency over 16%

High‐Efficiency Organic Solar Cells Based on a Low‐Cost Fully Non‐Fused Electron Acceptor

Asymmetrically noncovalently fused-ring acceptor for high-efficiency organic solar cells with reduced voltage loss and excellent thermal stability