Abstract:The aerospace industry is gradually moving toward “more electric aircraft” to reduce its environmental footprint. Developing all-electric actuators brings a reliability challenge because conventional geared-motor actuators are susceptible to jamming failures from their metal-to-metal gear contacts. Magnetorheological clutch actuators solve this challenge using a layer of fluid to transmit torque and are not exposed to potential jam failures, making them particularly attractive for high reliability applications such as primary flight controls. A key challenge that must be addressed for a widespread deployment of the magnetorheological fluid technology in aerospace is the ability to monitor magnetorheological fluid condition while it degrades in operation. To date, no such efforts have been reported in the literature. Recent studies on magnetorheological fluid durability have shown that mixing the magnetorheological fluid using a magnetic screw pump principle can significantly increase the life of the fluid by up to 50%. This article presents the design, prototyping, and testing of a proof-of-concept magnetorheological fluid condition monitoring sensor, capitalizing on the flow-recirculating properties of magnetic screw magnetorheological clutches to continuously provide a well-mixed and homogeneous fluid sample to the sensor. The proposed sensing principle uses optical red green blue sensor placed in the fluid circulation path to measure the fluid color during degradation. The sensor has been tested up to fluid failure on a high-torque (60 N m) magnetorheological clutch mounted on a fully instrumented durability test bench. Tests have been performed with two types of fluid: a commercially available fluid, the Lord 140CG, and a homemade fluid based on perfluoropolyether oil, the GPL-103. Results with the Lord fluid demonstrate a strong correlation between the decrease in torque-to-current performance with fluid brightness. The average of three aging tests on Lord 140CG fluid show a 12% ± 1% decrease in brightness at end-of-life regardless of operating conditions such as torque, shear rate, and dissipated power. These results suggest that, for the Lord 140CG fluid, brightness is directly linked to the fluid degradation state and independent of operating conditions, which makes it a more accurate metric to quantify durability than life dissipated energy since the latter can vary significantly depending on operating conditions. Tests made with the GPL-103 based fluid did not show such a strong correlation, which means that optical sensing of magnetorheological fluid condition must be carefully calibrated for each individual fluid and clutch design. Results from this study suggest that optical sensing is a relevant method to measure the magnetorheological fluid condition in flow-recirculating clutches.

Magnetoelastic Viscosity Sensor for Lubricant Oil Condition Monitoring

Vibration Viscosity Sensor for Engine Oil Monitoring Using Metal Matrix Piezoelectric Composite

Elasto-magneto-electric (EME) Sensors for Force Monitoring of Prestressing Tendons

Sensor Applications of Soft Magnetic Materials Based on Magneto-Impedance, Magneto-Elastic Resonance and Magneto-Electricity

Measurement of Lubricant Viscosity and Metal Particles Using Dual Coil Inductive Sensor

Real-Time and Online Lubricating Oil Condition Monitoring Enabled by Triboelectric Nanogenerator

Photonic Low Cost Micro-Sensor for in-Line Wear Particle Detection in Flowing Lube Oils

Bench Testing of Sensors Utilized for In-Line Monitoring of Lubricants and Hydraulic Fluids Properties

Study of Dynamic Viscoelasticity of a Mineral Oil-Based Magnetic Fluid

An optical red green blue sensor for monitoring the degradation of magnetorheological fluids in flow-recirculating high-torque clutch actuators

Automatic measurement of field-dependent elastic modulus and damping by laser Doppler vibrometry

Research on High Sensitivity Oil Debris Detection Sensor Using High Magnetic Permeability Material and Coil Mutual Inductance

Study on a High Sensitive Online Sensor for Wear Particles in Lubricant

A Synchronous Sensing Method of Measuring Lubricating Oil Film Thickness and Temperature by Using Eddy Current Effect

Friction assessment of ultralow viscosity lubricant formulations based on a validated elastohydrodynamic simulation

Theory, Instrumentation and Applications of Magnetoelastic Resonance Sensors: A Review

Research on Online Synchronous Sensing Method for Debris and Moisture in Lubricating Oil

Magnetoelastic Resonance Sensors: Principles, Applications, and Perspectives

An online wear metal particles monitoring warning sensor based on electromagnetic induction in lubricating oil

In situ monitoring of the iron content in magnethorheological rotary actuators