Abstract:Different food processing parameters may alter starch granule structure and its cooking degree. With lower thermomechanical energy, more resistant starch (RS) is retained in the food, which may benefit gastrointestinal (GI) health. The objective of this study was to determine the effect of food processing on dietary utilization and dog gut health. Experimental diets containing 56% corn as the sole starch source were produced through pelleting, baking, and extrusion and compared to a baked control diet in which the corn was replaced with dextrose. The extruded diet resulted in the highest level (P < 0.05) of in vitro starch cook and lowest RS, while baked was intermediate and pelleted had the lowest starch cook and highest RS. To evaluate the in vivo effects of these treatments, 12 dogs were adapted to foods for 9 d, and feces were collected for 5 d in a replicated 4 × 4 Latin square design. Feces were scored for consistency using an ordinal scale, and parametric data included apparent digestibility (ATTD), parameters indicative of gut health, and the microbial composition, which was centered log-ratio transformed before operational taxonomic unit (OTU) analyses. Fecal scores were analyzed by ordinal logistic regression, and parametric data were analyzed as mixed models. Overall ATTD was greater (P < 0.05) in extruded, followed by baked and pelleted. Dogs fed the control had osmotic diarrhea, whereas dogs fed the other treatments had mostly acceptable fecal scores, with extrusion leading to the best fecal quality. The control also led to high fecal pH and low SCFAs, indicating dysbiosis. All corn foods had similar (P > 0.05) fecal SCFAs and extruded tended (P = 0.055) to promote higher fecal butyrate than baked and pelleted. The microbiome of dogs fed the corn foods had similar α diversity indices, and OTUs at the species and phyla levels were mostly alike and different from the control. In conclusion, the higher levels of in vitro RS did not translate into a better in vivo fermentation profile, and extruded kibble performed best regarding fecal quality, ATTD, and fecal SCFAs.

A model that predicts resistant starch in a dog kibble using a small-scale twin-screw extruder

Extrusion Processing Modifications of a Dog Kibble at Large Scale Alter Levels of Starch Available to Animal Enzymatic Digestion

Influence of process parameters and added starches on resistant starch content and sensory properties of maize extrudates

Processing of corn-based dog foods through pelleting, baking and extrusion and their effect on apparent total tract digestibility and colonic health of adult dogs

Study on optimization of the extrusion processing of resistant starch by response surface methodology

Empirical Modeling of Die Pressure, Shaft Torque, SME, and Product Temperature of Rice Flour in a Corotating Twin‐Screw Extruder

Effect of Citrus Pellet on Extrusion Parameters, Kibble Macrostructure, Starch Cooking and In Vitro Digestibility of Dog Foods

SME‐Arrhenius Model for WSI of Rice Flour in a Twin‐Screw Extruder

Empirical Modeling of Mean Residence Time in a Co‐Rotating Twin‐Screw Extruder with Rice Flour

Relationship Between System Parameters and Target Parameter of Extrusion in Resistant Rice Starch Preparation

Optimization of Twin-Screw Extrusion Process to Produce Okara-Maize Snack Foods Using Response Surface Methodology

Effect of process parameters on slowly digestible and resistant starch content in extrudates.

At-line Prediction of Gelatinized Starch and Fiber Fractions in Extruded Dry Dog Food Using Different Near-Infrared Spectroscopy Technologies

Numerical modeling of fill-level and residence time in starve-fed single-screw extrusion: a dimensionality reduction study from a 3D CFD model to a 2D convection-diffusion model

Introduction to Modelling the Correlation Between Grain Sizes of Feed Material and the Structure and Efficiency of the Process of Co-Rotating Twin-Screw Extrusion of Non-Flammable Composites with a Pla Matrix

PSVI-29 Post-Extrusion In-vitro Fermentability of Fiber in Extruded Dog Foods

Design of Double-Roller Anisotropic Force-Feeding Device for the D200 Single Screw Straw Fiber Extruder

Predicting the Non-Linear Conveying Behavior in Single-Screw Extrusion: A Comparison of Various Data-Based Modeling Approaches used with CFD Simulations

129 Protein and Amino Acid Modifications During Extrusion

Simulation of Running Stability in a Twin Screw Extruder for Wet Extrusion of Fish Protein

An Innovative Approach for Significantly Increasing Enzyme Resistant Starch Type 3 Content in High Amylose Starches by Using Extrusion Cooking