Abstract:Glass ceramics are widely used to manufacture esthetic veneers, inlays, onlays, and crowns. Although the clinical survival rates ofglass-ceramic restorations arefavorable,fractures or chips are common. Certain cases can be repaired with direct composite. Aim: The aim of this study was to investigate the interaction effect of different designs and surface treatments on the load-to-failure of lithium disilicate glass-ceramic repaired with nanofilled composite. Materials and method: Lithium-disilicate glass-ceramic slabs (IPS e.max Press, Ivoclar Vivadent) with three different designs of the top surface (flat, single plateau, or doubleplateau) (n=U) received 'no treatment', '5% HF etching', or "AI2O3 sandblasting". HF-etched and sandblasted slabs also received silane and universal one-step adhesive application. All slabs were incrementally repaired with nanofilled composite (Filtek Z350, 3M ESPE) up to6 mm above the highest ceramic top plateau. Specimens were stored in artificial saliva at 37 °C for 21 days and then subjected to 1,000 thermocycles between 5 and 55 °C. The interface composite-ceramic of each specimen was tensile tested until failure in a universal testing machine and the mode of failure was determined under a stereomicroscope. The ceramic surface morphology of one representative tested specimen from each subgroup (design/surface treatment) was observed through scanning electron microscopy (SEM). Results: Regardless of ceramic design, the absence of surface treatment resulted in significantly lower load-to-failure values. No significant differences in load-to-failure values were observed between HF-etched and sandblasted specimens for the flat design; however, HF etching resulted in significantly higher load-to-failure values than sandblasting for both single plateau and double plateau designs. The majority (60%) of HF-etched specimens with single plateau or double plateau presented mixed failures. SEM photomicrographs showed that HF-etched specimens had smoother surfaces than sandblasted specimens. Conclusion: The surface treatment of a defective lithium disilicate glass-ceramic restoration has more influence than its macroscopic design on the retention of the composite repair. HF etching seems to provide higher bond strength to the composite repair.

Coating glass-ionomer cements with a nanofilled resin

Effects of Incorporation of Nano-Fluorapatite or Nano-Fluorohydroxyapatite on a Resin-Modified Glass Ionomer Cement

Effect of Nanofilled Resin-Based Coating on the Compressive Strength of Glass Ionomer Cement – in vitro

Protective effect of a nanofilled resin-based coating on wear resistance of glass ionomer cement restorative materials

Evaluating the Mechanical Properties of Restorative Glass Ionomers Cements

Mechanical Properties and Ion Release from Fibre-Reinforced Glass Ionomer Cement

Effect of Early Water Exposure on the Strength of Glass Ionomer Restoratives

Effect of a novel coating material on the microleakage of glass hybrid restoration in primary teeth – An in vitro study

Enhancement of dentin bond strength of resin cement using new resin coating materials

[Effect of Hydrofluoric Acid Etching Time and Resin Bonding on the Flexural Strength of Lithium Disilicate Glass Ceramic].

Effect of different design and surface treatment on the load-to-failure of ceramic repaired with composite

Evaluation of setting kinetics, mechanical strength, ion release, and cytotoxicity of high-strength glass ionomer cement contained elastomeric micelles

The Effect of Different Coating Agents on the Microhardness, Water Sorption, and Solubility of EQUIA Forte® HT

Effect of Etching Time and Resin Bond on the Flexural Strength of IPS E.max Press Glass Ceramic.

Using Functionalized Micron-Sized Glass Fibres for the Synergistic Effect of Glass Ionomer on Luting Material

Effect of a novel glass ionomer cement containing fluoro-zinc-silicate fillers on biofilm formation and dentin ion incorporation

Pre-cementation treatment of glass-ceramics with vacuum impregnated resin coatings

Effect of E-glass fibers addition on compressive strength, flexural strength, hardness, and solubility of glass ionomer based cement

Mechanical performance of encapsulated restorative glass-ionomer cements for use with Atraumatic Restorative Treatment (ART)

Effects of Environmental Calcium and Phosphate on Wear and Strength of Glass Ionomers Exposed to Acidic Conditions.

Influence of dentin conditioning with polyacrylic acid on the shear bond strength of a nano-filled resin-modified glass ionomer cement.