Abstract:Abstract In this work, experimental investigation was carried out on xanthan gel and xanthan foam rheology employing a pipe flow viscometer at 1000 psi. A nominal 1/2" stainless steel pipe was used as the flow conduit. Xanthan concentrations of 20, 30, and 40 lb/Mgal were used as the gelling agent to prepare xanthan fluids. Surfactant at 0.5% (vol.) was used as the foaming agent. Nitrogen was used as the gas phase. Foams were prepared and tested for qualities ranging from zero to 80% at various shear rates and at temperatures ranging from 75 to 200 °F. The flow data showed that both xanthan gel and xanthan foam exhibited a behavior analogous to Herschel-Bulkley model fluids. It was found that the foam viscosity increases as the foam quality increases and more viscous liquid phase generated higher foam viscosities. The increase of temperature had an adverse effect on foam viscosity and stability. Viscosity isotherms were generated for the xanthan foam. New empirical correlations for the xanthan gel and xanthan foam have been developed from the experimental data generated. These correlations are functions of liquid phase properties and foam quality and can be used to predict apparent viscosity of foam fluids for the conditions investigated. The use of these new correlations will provide a better estimation of the xanthan gel and xanthan foam fluid rheological properties. Introduction As the Petroleum Industry continues to explore new ways of finding and producing energy at an effective cost, the demand for new technology and innovations continue to grow. The application of foam fluid system in the petroleum industry is gaining wider acceptance, due to the ability to modify the many desirable properties of foam fluids for oil field operations.1 Foam fluid can now be tailored to have high carrying capacity, low density, low filtrate, and circulation losses, thus making it an ideal fluid for an underbalanced drilling. Foam fluids are also used as fracturing fluid, because in addition to their high carrying capacity, they can be fully recovered since only a small amount of the liquid is placed in the fracture. 2,3 Foam fluids used in the petroleum industry for fracturing, drilling or completion operations are prepared by mixing a liquid, a gas and a surfactant. The mixture is very complex and its rheological properties - shear stress, shear rate, and viscosity are strongly determined by the operating temperature, pressure, liquid phase properties, foam quality, foam stability, foam texture, foam channel wall interaction, and the type and concentration of the surfactant. Changes in these parameters affect the flow properties of the foam fluid and may seriously change their hydraulic behavior. This effect in turn may affect their stored energy, viscosity and the prediction of friction losses.4,5 This necessitates the search for new foam fluid systems and the study of their rheology, so as to overcome the problems. For these reasons an experimental investigation was conducted to find out the potential of using xanthan gum as the gelling agent. The effects of liquid phase, temperature, shear rate, and quality on the rheological properties of xanthan foam were investigated using a foam loop (pipe viscometer) available at the Well Construction Technology Center (WCTC) of the University of Oklahoma. Experiments were carried out at 1000 psia in 1/2-inch pipe over a wide range of temperature (75 to 200 °F), using 20, 30, and 40 lb/Mgal concentrations of xanthan gel, and nitrogen gas. Different foams that varied in qualities from zero to 80% were prepared and investigated at different shear rates to determine the corresponding shear stresses. The investigation was confined to the laminar flow regime.

Effect of high reservoir pressure on rheological properties of branched xanthan gum and polymer flooding behavior in porous media

Optimization of Recovery under Injection of Biopolymer, Synthetic Polymer and Gels in a Heterogeneous Reservoir

Production Optimization under Injection of Biopolymer, Synthetic Polymer and Gels in a Heterogeneous Reservoir

In Situ Crosslinking of Hyperbranched Polyglycerol in Casting Solutions and Its Effect on the Structure and Properties of Porous Pvdf Membranes

Host-guest strategy improves rheological properties, conformational stability and oil displacement efficiency of xanthan gum

Assessment of xanthan gum and xanthan-g-silica derivatives as chemical flooding agents and rock wettability modifiers

Assessment of a Novel Xanthan Gum-Based Composite for Oil Recovery Improvement at Reservoir Conditions; Assisted with Simulation and Economic Studies

Geo-engineering properties of expansive soil treated with xanthan gum biopolymer

Temperature/salt tolerance and oil recovery of xanthan gum solution enhanced by surface-modified nanosilicas

Multi-supramolecular and double-network strategy improves rheological properties and oil displacement efficiency of polymers

Viscosity and Structure Characterization of the 1-Bromohexadecane-Modified Welan Gum in the Saline Solution

Modification of Xanthan Gum for a High-Temperature and High-Salinity Reservoir

Rational modification of xanthan gum based on assistance of molecular dynamics simulation

Investigation into Xanthan Gum Biopolymer on Mitigating Cracking and Erosion Behavior of Soil

Experimental Study on the Physical and Mechanical Properties of Modified Clay Using Xanthan Gum and Guar Gum Composite Materials

Experimental Investigation of Xanthan Foam Rheology

Alleviation of the plastic deformation of gel ink under strong stress through an esterification of xanthan gum reinforcing its double helix structure

Study on increasing polymer gel strength with Janus nanoparticles and its feasibility in profile control and water plugging

Effective Modified Xanthan Gum Fluid Loss Agent for High-Temperature Water-Based Drilling Fluid and the Filtration Control Mechanism

Rheological Properties of Gel Foam Co-Stabilized with Nanoparticles, Xanthan Gum, and Multiple Surfactants

Experimental study on the plugging and profile control of preformed particle gels in high temperature and salinity reservoir