Abstract:The article is the continuation of a cycle of works published in a Special Issue of MDPI entitled "Innovative Technologies and Materials for the Production of Mechanical, Thermal and Corrosion Wear-Resistant Surface Layers and Coatings" related to tests concerning the microstructure and mechanical properties of innovative surface layers made using the Powder Plasma Transferred Arc Welding (PPTAW) method and intended for work surfaces of drilling tools and machinery applied in the extraction industry. A layer subjected to tests was a metal matrix composite, made using powder based on a nickel alloy containing spherical fused tungsten carbide (SFTC) particles, which are fused tungsten carbide (FTC) particles and spherical particles of tungsten-coated synthetic metal-diamond composite (PD-W). The layer was deposited on the substrate of low-alloy structural steel grade AISI 4715. The results showed that the chemical composition of the metallic powder as well as the content of the hard phase constituting the matrix enabled the making of a powder filler material characterised by very good weldability and appropriate melting. It was also found that the structure of the Ni-WC-PD-W layer was complex and that proper claddings (characterised by the uniform distribution of tungsten carbide (WC)) were formed in relation to specific cladding process parameters. In addition, the structure of the composite layer revealed the partial thermal and structural decomposition of tungsten carbide, while the particles of the synthetic metal-diamond composite remained coherent. The deposited surface layer was characterised by favourable resistance to moderate dynamic impact loads with a potential energy of 200 J, yet at the same time, by over 12 times lower metal-mineral abrasive wear resistance than the previously tested surface layer made of cobalt-based composite powder, the matrix of which contained the hard phase composed of TiC particles and synthetic metal-diamond composite. The lower abrasive wear resistance could result from a different mechanism responsible for the hardening of the spherical particles of the hard phase susceptible to separation from the metal matrix, as well as from a different mechanism of tribological wear.

Regeneration of Aluminum Matrix Composite Reinforced by SiCp and GCsf Using Gas Tungsten Arc Welding Technology

Mechanical Behavior of Gas Tungsten Arc Surface Modified Composite Layer on Mg Alloy AZ31 with SiCp and Aluminum

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Matrix Composite Coatings Deposited on AISI 4715 Steel by Powder Plasma-Transferred Arc Welding. Part 3. Comparison of the Brittle Fracture Resistance of Wear-Resistant Composite Layers Surfaced Using the PPTAW Method

Effect of Carbon in Fabrication Al-SiC Nanocomposites for Tribological Application

The properties of gas tungsten arc deposited SiCP and Al surface coating on magnesium alloy AZ31

Plasma arc welding of SiCp/Al MMCs based on in-situ weld-alloying

Degradation of SiC particles in aluminium-based composites

In-situ formation Ti-Al-C compounds reinforced SiCp/2A14 Al joint: Microstructure evolution and mechanical properties

An appraisal of characteristic mechanical properties and microstructure of friction stir welding for Aluminium 6061 alloy – Silicon Carbide (SiCp) metal matrix composite

<i>In situ</i> study on fracture behaviors of SiC/2A14Al composite joint: Co-construction of microstructure and mechanical properties via laser welding

Recovery of metal matrix composite drilling tools using a WC-Ni/Cr TIG-hardfacing technology

Microstructure, Corrosion and Mechanical Properties of TiC Particles/Al-5Mg Composite Fillers for Tungsten Arc Welding of 5083 Aluminum Alloy

Effect of Ti–Si–Mg-Al Wire on Microstructure and Mechanical Properties of Plasma Arc In-Situ Welded Joint of SiCp/Al Composites

Effects of reinforcements in Al 5052 and AZ31B explosively weld composites

Microstructure and Mechanical Properties of Friction Stir Welded SiC/TiB2 Reinforced Aluminum Hybrid Composites

Enhancement of Wettability of Aluminum Based Silicon Carbide Reinforced Particulate Metal Matrix Composite

Microstructure and Mechanical Properties of Gta Surface Modified Composite Layer on Magnesium Alloy Az31 with Sicp

Microstructure Features of In-situ SiCp/6061Al in Plasma Arc Welding by New Reinforced Phase