Abstract:Nowadays, technologies of chemical action on a rock mass, including the injection of polymer resins, the filling of voids by plugging with foaming compounds etc., are widely used to stabilize, to strength fractured rocks and to waterproof underground mines during development of solid minerals. In the paper we consider the issues of enhancing of the physical and mechanical properties of loose sedimentary rocks by chemical grouting with dual-component polymer resins. We perform laboratory experiments to strength fine-grained siliceous sand by the dual-component silicate-isocyanate and the foamed polyurethane resins. The grouting is performed through 10 cm diameter columns, which are filled with fine-grained siliceous sand. The main particle size fraction of the used sand is 0,150 – 0,210mm. The resin pumping into the test samples is carried out by two methods. The first method consists in sequential pumping of separate components of the polymer compounds. In this case, the solidification of the polymer compositions begins inside the rock sample. The second method consists in pumping of the fully prepared polymer compounds (two components are mixed immediately before injection in the rock sample). In this case, the solidification of the polymer compositions begins before the pumping in the rock, which leads to a rapid increase of the viscosity of the injected compositions. For both methods, the pumping is performed both with a pulse pressure increase and with a gradual (stepwise) pressure increase in the range from 0 to 15 bar. Based on the experimental results, the volume of the strengthened sand is determined. It was obtained that the volume of the strengthened (consolidated) sand is on average 2-3.5 times greater with separate-component injection, than with the injection of fully prepared compositions. For both pumping methods, a larger volume of consolidated rock is provided with a gradual (stepwise) pressure increase. Cylindrical specimens are cut out of the consolidated sand, and deformation-strength and filtration tests of the obtained material are carried out. The results show that the sequential pumping of separate components of the dual-component polymer compounds provides the greatest rock strengthening. It is obtained that the hardened sand uniaxial compressive strength is on average 1,5 times more for the sequential pumping of separate components compared to the injection of the fully prepared compositions. Similarly, the deformation modulus of hardened sand is 2,5 - 6 times more for the sequential pumping of separate components compared to the injection of the fully prepared compositions. The use of the dual-component silicate-isocyanate compositions provides more effective strengthening of loose sedimentary rocks compared to the foaming polyurethane compositions. The uniaxial compressive strength and the deformation modulus of the consolidated fine-grained sand are on average 10 - 12 times more for the dual-component silicate-isocyanate compositions compared to the foaming polyurethane compositions. The obtained data can be used to select and optimize the method of pumping of dual-component polymer compositions to stabilize disturbed mines.

Laboratory study of properties of sand grouted by dual-component resins

Sedimentation-affected Engineering Performances and Microstructures of a Hybrid Portland- Sulfate Aluminate Cement Grout Cast in Long Tubes

Comparative study on the mechanical properties of solidified silty-fine sand reinforced by permeable polymer and traditional grouting materials

Experimental and numerical study of the effect of polymer flooding on sand production in poorly consolidated porous media

Experimental study on new grouting material of acidic sodium silicate and its properties of grouted-sand

Influence of polyurethane in the polymerization process for poorly graded sand stabilization and cementing

The Effect of Polymer-Fiber Stabilization on the Unconfined Compressive Strength and Shear Strength of Sand

Strength and permeability properties of sodium silicate-glyoxal stabilised silt and fine sand

Study on Grouting Performance Optimization of Polymer Composite Materials Applied to Water Plugging and Reinforcement in Mines

Strength for Modified Polyurethane with Modified Sand

Strength Assessment of Water-Glass Sand Mixtures

Experimental study on the mechanical behaviour of silty soil stabilized with polyurethane

Innovative Ground Improvement with Chemical Grouts: Potential and Limits of Partial Saturation with Polymers

Sandstone chemical consolidation and wettability improvement using furan polymer-based nanofluid

Polyacrylamide hydrogel application in sand control with compressive strength testing

Experimental investigation and discrete element method simulation on mechanical properties and failure mechanism of polymer-stabilized sand

Study on the Gelation Process and Mechanical Properties of Organic Polymer Grouting Materials Applied to Fissure Sealing in Underground Mines

Experimental Study on the Diffusion Characteristics of Nonaqueous Reactive Expansive Polymers in Sand and Gravel Media under Dynamic Water Conditions

An experimental study of the effect of cement and chemical grouting on the improvement of the mechanical and hydraulic properties of alluvial formations

Geopolymer Materials for Low-Pressure Injections in Coarse Grained Soil: Multiscale Approach to the Study of the Mechanical Behaviour and Environmental Impact

A New Laboratory Technique to Enhance Proppant Consolidation During Propped Hydraulic Fracturing Treatment