Abstract:Threaded fasteners were developed long time (let’s remember that Archimedes – 287-212 BC – invented the water screw). Nowadays, bolted joints are used in almost all sectors of the industry. But in spite of having been an important machine part for centuries, problems may be encountered with them. They are so common that they are taken for granted and too often, not analyzed as deeply as it should be. The wrong tightening is one of the most frequent causes of ductile rupture and by far the most frequent cause of fatigue failure. The tightening operation is never easy. It is necessary to pay particular attention to the choice of the tightening tool, the process and the control method. The tightening operation may itself cause damage on parts. The tightening load must not be too low, or excessive or not equally distributed among the bolts. These three defects can even be made on the same bolted joint! This impacts badly the performance of the assembly and leads to a shorter lifespan. If insufficient precautions are taken, the real tightening preload on all the bolts will not fit well with the requirements and would be badly distributed. Consequently, the practical conditions are quite different from the hypothesizes which are taken for the initial calculations (analytics or FEM) at the design stage. Thus, the results of the calculations of bolted joints cannot be considered as accurate and reliable. Practically, there are several means to tighten a bolt. The two ways most frequently used are torque wrench and hydraulic bolt tensioner. Torque wrench involves exerting a torque to the bolt head or the nut. Hydraulic bolt tensioner applies a traction load directly on the bolt. It is well known that bolt tensioners give better accuracy and homogeneity in the final tightening load than the torque method, but the tension load applied with the tensioner must be higher than the final remaining tightening load. So, the paper focusses on the hydraulic tensioner to show how the tightening load can be obtained from the applied tension load and to propose a way to optimize and secure the tightening process. However, for the reasons above mentioned it appears necessary to first make a general description of technical aspects of bolted joints. What really happens when tightening with torque wrench or with bolt tensioner is explained.

Analysis of the Tightening Process and the Cyclic Stress Amplitude of Studs and Tap Bolts

Analyses of Tightening Characteristics and Cyclic Stress Amplitude of Studs and Tap Bolts

FEM-based Multi-field Coupling Stress Analyses of the Cylinder-bolts System in a Gas Turbine Power Plant

FINITE ELEMENT ANALYSIS OF STIFFENED T-STUB CONNECTIONS

Experimental investigation of mechanical behavior of grade 8.8 and 10.9 small-sized (m14-m20) bolts with the thread into the bolt hole

Three-dimensional finite element analysis of tightening and loosening mechanism of threaded fastener

Test on shear behavior of less-tightened high-strength bolted connections

Effect of Interference Fit Size on Local Stress in Single Lap Bolted Joints

Finite element analysis of bolted joints under torsional loads

Three-dimensional finite element analysis of tightening and untightening process of bolt and nut connections with slight pitch difference

The Tightening and Untightening Modeling and Simulation of Bolted Joints

Torsional and compressive properties of bolted joint under forward-reverse tightening

Degradation and failure analysis of bolted joints under transverse loading

Research on bolt pre-tightening and relaxation mechanism under transverse load

A New Tightening Method for Bolted Joints by the Simultaneous Application of Torque and Compressive Force

Investigation of bolt clamping force on the fatigue life of double lap simple bolted and hybrid (bolted/bonded) joints via experimental and numerical analysis

Ultimate Tensile Behavior of Bolted T-stub Connections with Preload

Optimal tightening process of bolted joints

Stress-conversion-based Approach of High-cycle Fatigue Strength Analysis for Internal Threads

Optimizing fatigue life prediction of high strength bolts in bolted spherical joints

Experimental Study of Constant-Amplitude Fatigue Performance of M39 High-Strength Bolts in Grid Structures with Bolt-Sphere Joints