Abstract:Epoxy resin has been widely used in electronic and electrical equipment due to its excellent electrical and mechanical properties. However, prolonged corona discharge may cause deterioration of the surface, and finally lead to failure of insulation structure. Extensive researches have indicated that addition of nano fillers can improve corona resistance of polymers. In this paper, epoxy/SiO2 nanocomposites are prepared to study the micro development of corona erosion and surface trapping performance during corona aging. AC breakdown strength of epoxy/SiO2 nanocomposites is measured firstly and 2 wt% epoxy/SiO2 nanocomposite with highest AC breakdown strength of 64.11 kV/mm is selected to conduct corona resistance test with pure epoxy. It was observed by polarizing microscope that the degradation was severer for pure epoxy resin with corrosion area from about 0.27 mm2 at 10 min to 0.57 mm2 at 30 min, while the area of 2 wt% nano-SiO2 nanocomposite is nearly invariable about 0.21 mm2. With the increase of corona duration, the corrosion regions become darker which indicates thicker channel and more intensive corrosion density. Additionally, the corona damage extends from the center to edge of samples in shape of “branch”, and “branch” channels of degradation develop denser in the center. The isothermal surface potential decay (ISPD) results show that shallow trap ranges from 0.90 to 1.00 eV, whereas the deep trap locates at 1.05∼1.15 eV. The deep energy density of pure epoxy decreases dramatically from 7.2x1014 m−3 to 4.9x1014 m−3 with corona aging time, while that of 2 wt% epoxy/SiO2 nanocomposite maintains constant about 6.9x1014 m−3. Both of the shallow trap density of epoxy and nanocomposite increases after corona aging, while pure epoxy increases more obvious from 1.6x1013 m−3 to 3.8x1013 m−3. Therefore, charges are more difficult to inject and move in epoxy nanocomposites because of more deep traps even after corona exposure, which illustrates why nanocomposites have higher corona resistance.

A study on environmental stress cracking in nano-SiO2-filled polycarbonate

Environmental stress cracking (ESC) resistance of polycarbonate/SiO2 nanocomposites in different media

Polycarbonate/Titania Composites Incorporating TiO2 with Different Nanoscale Morphologies for Enhanced Environmental Stress Cracking Resistance in Dioctyl Phthalate

The Influence of Environmental Stress Cracking (ESC) and Gamma Irradiation on the Mechanical Properties of Polycarbonate: Study of Synergistic Effects

Mechanical and Rheological Properties of PC Composite Filled with Modified SiO_2 Nanoparticles

Silicon Carbide Nanoparticles as a Mechanical Boosting Agent in Material Extrusion 3D-Printed Polycarbonate

Studying the influence of the addition of nano-titanium dioxide on the rheological, mechanical, thermal, and electrical properties of polycarbonate/wood flour

Effect of Al2O3 and SiC Nano-Fillers on the Mechanical Properties of Carbon Fiber-Reinforced Epoxy Hybrid Composites

Simulation and Experimental Study on Micro-Crack Toughening Mechanism for Attapulgite/Epoxy Nanocomposite

Cracking Stress of Nano-Fibers Composite Ceramics

The Effect of Electrically Pre-stressing of High Field Conduction in the Nanocomposite of Polyethylene and Nano-SiO_x

Cellulose nanocrystals as organic nanofillers for transparent polycarbonate films

Study on the Reinforcing Effect of Nano-Sio2 Filled PTFE Composites

Study on Solvent Resistance and Crystallization Behavior of PCA/PA6

Wear‐ and UV‐resistant polycarbonate‐based composite films reinforced by a novel inorganic–organic hybrid filler

Residual stress and interface debonding behavior in Si3N4w reinforced SiCN composites prepared by the PIP process: A case study

Surface Corona Aging of Epoxy/SiO2 Nanocomposites

Effect of Wet Surface Treated Nano-Sio2 on Mechanical Properties of Polypropylene Composite

Overload-induced retardation of fatigue crack growth in polycarbonate

Experimental Study on the Bending Property of Nano-silica Incorporated GF/PCBT Composites Exposed under Various Environmental Conditions

Study on Delamination Failure Mechanism of Polycarbonate Thin-Walled Component