Abstract:Accelerated bridge construction, with innovative connection details and construction technologies, has been extensively investigated and put into practical application for years. Nowadays, there are three commonly used connection methods of accelerated bridge construction technology, namely, lap‐spliced connection, sleeve connection, and socket connection. Due to the convenience of construction and lower requirements of construction accuracy, the socket connection is more suitable for reconstruction and expansion projects of traffic infrastructure, which could minimize the impact on traffic and accelerate construction progress. According to the structural characteristics of the socket connection, there are some design parameters that may significantly affect the seismic resistance of the structure, such as socket embedment length, fabrication of the shear key, and grouting material strength. To fully study the influence of different design parameters on structural performance, an experiment was carried out to investigate the seismic behavior of the precast pier‐footing socket connections with different design parameters. Five 1:2 scale reinforced concrete precast pier‐footing socket connection specimens with different design parameters were designed and tested under cyclically reversed horizontal loads. The development of hysteresis features, failure mode, load‐bearing capacity, stiffness degradation, structural ductility, energy dissipation capacity, and residual drift are analyzed to reveal the influence of the different design parameters on the seismic behavior of the precast pier‐footing socket connection. The seismic behavior of the precast pier‐footing socket connection was significantly influenced by the embedment length especially when the embedment length was less than 1.0bc. When the embedment length was 0.5bc, the failure mode changed from bending damage at the bottom of the precast pier to the anchorage failure of the precast pier‐footing socket connection. When the embedment length was 1.5bc, the fabrication of the shear key had limited improvement on the seismic performance of the specimen, while reducing the ductility of the specimen. When the embedment length was 1.0bc, the grouting material with a strength grade of C60 could be used in the socket connection between the precast pier and footing. The research presented in this paper provides some design suggestions and a technical basis for evaluating the seismic behavior of precast pier‐footing structures with socket connection.

Shaking table test on single segment prefabricated concrete bridge pier connected by grouting sleeve

Experimental Studies on Seismic Behavior of Steel Pile-to-Pile-Cap Connections

Networked pseudodynamic testing of bridge pier and precast pile foundation

Research on the Factors Influencing the Seismic Performance of Grouting Sleeve Assembled Double-Column Piers

Precast segmental piers: testing, modeling and seismic assessment of an emulative connection based on a grouted central tenon

Shaking table tests of seismic-resilient post-tensioned reinforced concrete bridge piers with enhanced bases

Seismic performance of precast piers connected by grouted splice sleeve with Central-tenon enhancement: experimental validation and system-level fragility study

Experimental study on seismic response of precast bridge piers with double-grouted sleeve connections

Seismic Performance of FRP-Confined Precast Assembled Concrete Piers: An Experimental Study

Shaking Table Test on Seismic Performance of Continuous Rigid Frame Bridge with Cast-in-place and Fabricated Super High Piers

Seismic performance of precast piers with staggered longitudinal reinforcement-UHPC connection

Seismic performance of a new type of prefabricated bridge pier with cast-in-place UHPC jacketing

Seismic performance of bridge with unbonded posttensioned self-centering segmented concrete-filled steel-tube columns: An underwater shaking table test

Experimental investigation of seismic behavior of precast pier‐footing socket connection with different design parameters

Research on the Seismic Performance of Prefabricated Bridge Piers Using UHPC Grout under an Eccentric Load

Numerical Investigation of the Performance of Segmental CFST Piers with External Energy Dissipators under Lateral Cyclic Loadings

Shaking Table Test on Seismic Response of Pile Groups of Bridges in Liquefiable Ground

Seismic behaviors of precast assembled bridge columns connected with prestressed threaded steel bar: Experimental test and hysteretic model

Cyclic Loading Tests and Seismic Performance Evaluation of Arch-Shaped Concrete Masonry Segmental Pier with Annular Double Sliding System

Cyclic Loading Test and Numerical Modeling on Prefabricated UHPC Tube-Confined Rectangular Bridge Piers with Different Base Connections