Abstract:While significant work is being carried out to develop materials for enabling high surface charge density triboelectric nanogenerators (TENG), little attention has been paid to the role of electrodes responsible for charge collection. This work reports on the facile synthesis and use of high crystallinity, sp(2)-hybridised laser-induced graphene (LIG) as a high-efficiency electrode for triboelectric nanogenerators (TENGs). Using a conventional 10.6 mu m CO2 laser, the controlled, direct photothermal conversion of dielectric, tribo-negative polyimide (PI) and tribo-positive cellulosic paper into corresponding PI-LIG and paper-LIG, respectively, facilitates a significantly higher electrical output as compared to the commonly utilised adhesive aluminium electrodes. The LIG based paper-PI TENGs showed significantly higher electrical output characteristics with a peak-to-peak voltage of up to-625 V, a current density of-20 mA m(-2) and a transferred charge density of-138 mu Cm-2 with a maximum power output of-2.25 W m(-2), respectively, while the corresponding values for the conventional Al-tape electrode-based paper-PI TENGs were 400 Vp-p, similar to 10 mA m(-2), similar to 85 mu C m(-2) and 0.9 W m(-2), respectively. The mechanically robust LIG electrodes show excellent stability with less than 5.0% variation in output over 12,000 contact cycles. Using Kelvin probe force microscopy (KPFM) measurements, we have measured differences in not only the average surface potentials of the triboelectric surfaces (-0.26 V for pristine PI vs. +0.34 V for paper, which drive the TENG electrical output) but also for the LIG's synthesised from them (-0.08 V for PI-LIG vs. +0.26 V for paper-LIG), suggestive of the role of initial surface chemistry in the formation of LIGs. The enhanced (similar to 150%) power density for LIG based TENGs is ascribed to the lowering of the charge transfer barrier height via the alignment of Fermi levels resulting in higher surface charge on the dielectric surface and the significantly (similar to 6 orders) lower interfacial contact impedance of LIG as compared to adhesive aluminium electrodes. Thus, via the removal of the additional interface between the triboelectric surface and electrode, high-performance metal-free TENGs with excellent prospects for enabling energy harvesting applications can be realised.

Novel electrode material using electroless nickel plating for triboelectric nanogenerator: Study of the relationship between electrostatic-charge density and strain in dielectric material

Textile-based triboelectric nanogenerators via electroless plating for fabricating electrode material: Study of the relationship between electrostatic-charge density and strain in dielectric material

Carbon Electrodes Enable Flat Surface PDMS and PA6 Triboelectric Nanogenerators to Achieve Significantly Enhanced Triboelectric Performance

In Situ Sputtering Silver Induction Electrode for Stable and Stretchable Triboelectric Nanogenerators

Regulation of nanocrystals structure for high-performance magnetic triboelectric nanogenerator

Engineering of electrodes with 2D Ti3C2Tx-MXene sheets and chloride salt for robust and flexible high electrical power triboelectric nanogenerator

High Performance Triboelectric Nanogenerators with Aligned Carbon Nanotubes.

Development of flexible high-performance PDMS-based triboelectric nanogenerator using nanogratings

Replacing the Metal Electrodes in Triboelectric Nanogenerators: High-performance Laser-Induced Graphene Electrodes

A high-performance single-electrode triboelectric nanogenerator based on polydimethylsiloxane surface modified using zinc oxide nanotubes: Fabrication and simulation

Enhancing the Performance of Triboelectric Nanogenerator via Facile PDMS Surface Modification

Enhanced Triboelectric Output of PDMS-based Composite Film with Bi-Material Filling and Surface Patterning

Triboelectric Nanogenerators (tengs) Based on Various Flexible Polymeric Materials along with Printed and Non-Printed Electrodes

Investigating the Performance of Triboelectric Nanogenerators (tengs) Fabricated Using Various Flexible Polymeric Materials

Screen-printed Soft Triboelectric Nanogenerator with Porous PDMS and Stretchable PEDOT:PSS Electrode

Boosting the Electrical Performance of PLA‐Based Triboelectric Nanogenerators for Sustainable Power Sources and Self‐Powered Sensing

Dielectric materials for high-performance triboelectric nanogenerators

Fabrication, characterization and in vitro evaluation of triboelectric nanogenerator based on 317 L stainless steel and polylactic acid

Performance enhancement of transparent and flexible triboelectric nanogenerator based on one-dimensionally hybridized copper/polydimethylsiloxane film

Enhancing the Output Performance of a Triboelectric Nanogenerator Based on Modified Polyimide and Sandwich-Structured Nanocomposite Film

Investigated a Pll Surface-Modified Nylon 11 Electrospun as a Highly Tribo-Positive Frictional Layer to Enhance Output Performance of Triboelectric Nanogenerators and Self-Powered Wearable Sensors