Abstract:One of the major challenges in all-solid-state lithium-ion battery (ASSLiB) developments for electronic vehicles is to prevent crack formation in electrodes during charge and discharge. The crack forms due to the volumetric expansion caused by lithium ion insertion to active materials. Although X-ray or electron beam based analysis can provide, the cracks in the electrodes can be analyzed using limited and heavy cost analysis, that can be a hurdle to optimize durable battery design. In order to accelerate the structural analysis and the design optimization, a simulation technology to predict the structural changes has been highly desired. The electrode degradation involves complicated phenomena such as powder deformations, volumetric expansion of active materials caused by the lithium insertion, interface peelings on the powder interfaces and the crack formation. This complexity has been the main reason why the practical simulation methodology has not emerged so far. To address the issue, we propose a new simulation methodology based on a finite element method (FEM) combined with a density functional theory (DFT). In the electrode degradation simulation, we take a new FEM approach called multi-particle FEM (MP-FEM). Since many FEM work treat compacted powders as a continuum body, they cannot describe the peelings at the particle interfaces or cracks in the electrode. On the other hand, MP-FEM can describe these phenomena since MP-FEM treats each particle structures explicitly. We apply a tiebreak model to the particle interfaces for accurate simulation. To perform MP-FEM, material properties must be set properly. In evaluating the material properties, we recommend to apply DFT simulation at the same time with experimental evaluations. Normally, material properties are evaluated by tests. However, the precise evaluation is challenging and time consuming because of several reasons such that the evaluation on normal test piece cannot be applied since the target materials are powders with the diameters around 0.1~100 micro meter. To demonstrate the advantage of our methodology, we built an electrode model containing an active material (AM) and a solid electrolyte (SE). In the first step of the simulation, the model electrode was pressed. After the removal of the all pressure, pore volume ratio was predicted as 20%, which showed a good agreement with experimental value of 18%. In the second step, the AM powders were controlled to expand and shrink representing charge and discharge. Our model reproduced the brake down of connected powder interfaces indicating decrease of lithium conduction paths. The volumetric ratio of pores in the electrode decreased during the charge process which also showed a good agreement with an experimental finding that internal resistance of the electrode decreased during charge processes. Based on these results, we believe that the methodology can predict electrode durability. In this paper, we will also compare several electrodes with varied design parameters and discuss design guidelines for durable electrode design.

Numerical Investigation on Diffusion-Induced Cracking in Solid Electrolyte of Composite Electrode and Its Impact on the Li-Ion Conductivity

Sandwich-Lithiation and Longitudinal Crack in Amorphous Silicon Coated on Carbon Nanofibers

Diffusion-Induced Transient Stresses in Li-Battery Electrodes Imaged by Electrochemical Quartz Crystal Microbalance with Dissipation Monitoring and Environmental Scanning Electron Microscopy

Modeling of Void‐Mediated Cracking and Lithium Penetration in All‐Solid‐State Batteries

Electrochemo-mechanical response of all solid-state batteries: Finite element simulations supported by image-based 3D reconstruction of X-ray microscopy tomography

Modeling damage to the solid electrolyte matrix in composite electrodes: role of ionic conductivity

Computational Design Optimization of All-Solid-State Lithium Ion Battery Electrode by Multi-Scale Simulation Based on Finite Element Method Combined with Density Functional Theory

Time-frequency analysis of electrochemical-mechanical coupling in active particle of composite electrode for lithium-based all-solid-state batteries

In situ Observation of Li Deposition‐Induced Cracking in Garnet Solid Electrolytes

The Diffusion Induced Stress and Cracking Behaviour of Primary Particle for Li-ion Battery Electrode

Electrochemical-Mechanical Coupling Failure Mechanism of Composite Cathode in All-Solid-State Batteries

Modeling storage particle delamination and electrolyte cracking in cathodes of solid state batteries

Electro-chemo-mechanical behavior of lithium-ion battery electrodes

Atomic Mechanism of the Distribution and Diffusion of Lithium in a Cracked Si Anode

Review on Modeling for Chemo-mechanical Behavior at Interfaces of All-Solid-State Lithium-Ion Batteries and Beyond

Accelerated Li Penetration and Crack Propagation Due to Mechanical Degradation of Sulfide‐Based Solid Electrolyte

Role of Polymeric Binders on Mechanical Behavior and Cracking Resistance of Silicon Composite Electrodes During Electrochemical Cycling

A Fully Coupled Mechano-Electrochemical Model for All-Solid-State Thin-Film Li-Ion Batteries with Non-Porous Electrodes: Effects of Chemo-Mechanical Expansions on Battery Performance and Optimization Strategies for Stress Evolution

Influence of Crystallinity of Lithium Thiophosphate Solid Electrolytes on the Performance of Solid‐State Batteries

Molecular Insights into the Structure and Property Variation of the Pressure-Induced Solid Electrolyte Interphase on a Lithium Metal Anode.

Modeling the Electro-Chemo-mechanical Failure at the Lithium-Solid Electrolyte Interface: Void Evolution and Lithium Penetration