Abstract:Designing composite electrodes with optimal microstructure, composition, and choice of active material (AM) as well as solid electrolyte (SE) is critically important for the development of high-performance solid-state batteries (SSBs). To optimize AM loading, which includes loading amount, composition, and dispersion state, and to maximize AM utilization in composite SSB electrodes, we need to precisely understand how the AM loading affects electrochemical reactions taking place in the electrodes. Here, using computed tomography combined with X-ray absorption near edge structure spectroscopy (CT-XANES), we performed operando three-dimensional (3D) observations of electrochemical reactions in composite SSB electrodes with different AM loading amounts to understand the influence of the AM loading on the electrochemical reactions. In the composite electrode with higher AM loading amount, the lower reacted regions were mainly found at the inner parts of the aggregated AM regions. It was suggested that such a reaction distribution resulted from the slow intergranular ion transport between AM particles. In the composite electrode with lower AM loading amount, the electrochemical reaction progressed more homogeneously compared to the one with higher loading. This is probably because the lower AM loading mitigated the AM aggregation and decreased the number of high-resistance AM–AM interfaces that Li ions must pass through. Such a reaction distribution formation due to the slow ion transport between the AM particles can be a serious restriction in composite SSB electrodes. This is in marked contrast to conventional liquid-based lithium ion battery (LIB) electrodes, in which a majority of AM particles can directly exchange Li ions with the surrounding liquid electrolyte. Therefore, the optimal design for composite SSB electrodes can significantly differ from that for liquid-based LIBs. Our analysis technique can provide valuable information to rationally design optimal composite electrodes, and hence we expect that this technique contributes to the further development of high-performance SSBs.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.0c01186.XRD pattern and temperature dependence of conductivity of Li2.2C0.8B0.2O3; 3D and 2D charging state maps of composite electrodes with the weight ratio of LiCoO2:Li2.2C0.8B0.2O3 = 5:5 (55cell) and 8:2 (82cell) during (dis)charge (PDF)Movie S1: 3D reaction distribution evolution during (dis)charge in the 82cell (MPG)Movie S2: 3D reaction distribution evolution in the aggregated active material region in the 82cell during (dis)charge (MPG)Movie S3: 3D reaction distribution evolution during (dis)charge in the 55cell (MPG)Movie S4: 3D reaction distribution evolution in the aggregated active material region in the 55cell during (dis)charge (MPG)This article has not yet been cited by other publications.

Time-frequency analysis of electrochemical-mechanical coupling in active particle of composite electrode for lithium-based all-solid-state batteries

Clarifying the Electro‐Chemo‐Mechanical Coupling in Li 10 SnP 2 S 12 based All‐Solid‐State Batteries

Diffusion-Induced Transient Stresses in Li-Battery Electrodes Imaged by Electrochemical Quartz Crystal Microbalance with Dissipation Monitoring and Environmental Scanning Electron Microscopy

Diffusion and Induced Stress Tuning Mechanisms: Analytical Modeling of Species Transport in Silicon-Graphene Layered Composite Electrodes for Lithium Batteries

Spatial‐Dependent Coupling of Electrochemistry, Mass Transport, and Stress in Silicon‐Graphite Composite Electrodes for Lithium‐Ion Batteries

Numerical Investigation on Diffusion-Induced Cracking in Solid Electrolyte of Composite Electrode and Its Impact on the Li-Ion Conductivity

Influence of Active Material Loading on Electrochemical Reactions in Composite Solid-State Battery Electrodes Revealed by Operando 3D CT-XANES Imaging

A Fully Coupled Mechano-Electrochemical Model for All-Solid-State Thin-Film Li-Ion Batteries with Non-Porous Electrodes: Effects of Chemo-Mechanical Expansions on Battery Performance and Optimization Strategies for Stress Evolution

Electrochemo-mechanical response of all solid-state batteries: Finite element simulations supported by image-based 3D reconstruction of X-ray microscopy tomography

Electrochemical-Mechanical Coupling Failure Mechanism of Composite Cathode in All-Solid-State Batteries

Force-chemical coupling analysis of nanocomposite anode during charging and discharging process

Recent advance into understanding electro-chemo-mechanical behavior of lithium ion batteries by electron microscopy

Experimental and Modeling Analysis of Mechanical Response of Composite Electrodes in Lithium Batteries

A Multiscale Electrochemo-mechanical Model of Porous Electrode in Lithium-ion Batteries: The Coupling of Reaction and Finite Deformation

A Modeling Framework of Electrochemo-mechanics of Lithium-ion Battery: Part II. Porous Electrodes with Contact Stress Effect

Electro-Chemo-Mechanical Model for the Damage in Porous Electrodes of Lithium-Ion Batteries

Effect of Young's modulus of active materials on ion transport through solid electrolyte in all-solid-state lithium-ion battery

Unveiling Solid-Solid Contact States in All-Solid-state Lithium Batteries:An Electrochemical Impedance Spectroscopy Viewpoint

A Multi-Scale Heterogeneous Electrochemical-Diffusion-Induced Stress Coupling Model for Lithium-Ion Batteries

Quantitative Regulation of Electrochemical-Mechanical Performance of Composite Cathode in All-Solid-State Batteries

Stress Fields in Hollow Core–shell Spherical Electrodes of Lithium Ion Batteries