Abstract:Pulsed thermography is a commonly used non-destructive testing method and is increasingly studied for the assessment of advanced materials such as carbon fibre-reinforced polymer (CFRP). Different processing approaches are proposed to detect and characterize anomalies that may be generated in structures during the manufacturing cycle or service period. In this study, matrix decomposition using Robust PCA via Inexact-ALM is investigated as a pre- and post-processing approach in combination with state-of-the-art approaches (i.e., PCT, PPT and PLST) on pulsed thermography thermal data. An academic sample with several artificial defects of different types, i.e., flat-bottom-holes (FBH), pull-outs (PO) and Teflon inserts (TEF), was employed to assess and compare defect detection and segmentation capabilities of different processing approaches. For this purpose, the contrast-to-noise ratio (CNR) and similarity coefficient were used as quantitative metrics. The results show a clear improvement in CNR when Robust PCA is applied as a pre-processing technique, CNR values for FBH, PO and TEF improve up to 164%, 237% and 80%, respectively, when compared to principal component thermography (PCT), whilst the CNR improvement with respect to pulsed phase thermography (PPT) was 77%, 101% and 289%, respectively. In the case of partial least squares thermography, Robust PCA results improved not only only when used as a pre-processing technique but also when used as a post-processing technique; however, this improvement is higher for FBHs and POs after pre-processing. Pre-processing increases CNR scores for FBHs and POs with a ratio from 0.43% to 115.88% and from 13.48% to 216.63%, respectively. Similarly, post-processing enhances the FBHs and POs results with a ratio between 9.62% and 296.9% and 16.98% to 92.6%, respectively. A low-rank matrix computed from Robust PCA as a pre-processing technique on raw data before using PCT and PPT can enhance the results of 67% of the defects. Using low-rank matrix decomposition from Robust PCA as a pre- and post-processing technique outperforms PLST results of 69% and 67% of the defects. These results clearly indicate that pre-processing pulsed thermography data by Robust PCA can elevate the defect detectability of advanced processing techniques, such as PCT, PPT and PLST, while post-processing using the same methods, in some cases, can deteriorate the results.

Analysis of data processing methods for pulsed thermal imaging characterisation of delaminations

Studies on the Infrared Thermography Technique for Quantitative Nondestructive Evaluation of Surface Crack and Delamination of Multilayer Structures

3D photothermal reconstruction of subsurface defects in notched multidirectional CFRP laminates due to tensile fatigue loading

Visual Defect Recognition and Location for Pulsed Thermography Images Based on Defect-background Contrast Analysis

Effects of different excitation waveforms on detection and characterisation of delamination in PV modules by active infrared thermography

Nde of Composites Delamination by Infrared Thermography

Quantitative Evaluation of Crack Depths on Thin Aluminum Plate using Eddy Current Pulse-Compression Thermography

Quantitative non-destructive evaluation of CFRP delamination defect using laser induced chirp-pulsed radar photothermal tomography

Induction Infrared Thermography and Thermal-Wave-Radar Analysis for Imaging Inspection and Diagnosis of Blade Composites

A Novel Methodology to Predict 3-D Surface Temperature Field on Delamination for Thermography

Accurate Depth Determination of Defects in Composite Materials Using Pulsed Thermography

Gapped Smoothing Algorithm Applied to Defect Identification Using Pulsed Thermography

Pulse Phase Dynamic Thermal Tomography Investigation on the Defects of the Solid-Propellant Missile Engine Cladding Layer

Thermography Sequence Processing and Defect Edge Identification of TBC Structure Debonding Defects Detection Using Long-Pulsed Infrared Wave Non-Destructive Testing Technology

Data Enhancement via Low-Rank Matrix Reconstruction in Pulsed Thermography for Carbon-Fibre-Reinforced Polymers

Thermal non‐destructive testing and evaluation for inspection of carbon fibre‐reinforced polymers

Defect Detection Capabilities of Pulse Compression Based Infrared Non-Destructive Testing and Evaluation

Quantitative Detection of Defect Using Ultrasound Infrared Lock-In Thermography

Quantitative Test of Delamination Defects in CFRP with Surface Interference by Laser Thermography

Numerical Analysis of Heat Transfer Process in Pulsed Thermography Detection on Electrical Ceramic Materials

Time-Frequency Based Thermal Imaging: An Effective Tool for Quantitative Analysis