Abstract:In the ultra-large-scale integration (ULSI) technologies, polysilicon resistors are usually employed in the integrated circuits as a precise analog resistor element for a variety of applications, such as DAC (digital resistor give the solution of the linearity and Rs concerns to analog converter) in analogue circuits [1-3]. Conventionally the polysilicon resistance can be adjusted by ion implantation and post annealing process [4]. For the self-aligned implantation process, the dosage changes which are always utilized to adjust the resistance are feasible to induce the MOS characteristics changes, especially in the submicron process whose short-channel effects (SCE) are much more sensitive to the dosages [5]. In this work, we propose a new inner anneal process in N2ambient after polysilicon re-oxidation to reduce the polysilicon resistance by changing the polysilicon grain size. The test patterns are manufactured on 300mm-diameter wafer by 65-nm 1-poly 7-metal standard CMOS technology. After polysilicon re-oxidation to form oxide film on polysilicon surface, the wafers are annealed at 800oC, 900oC, 950oC and 1000oC in N2ambient, respectively. Fig. 1 shows the process flow and annealing process steps in the flow. After anneal, the polysilicon grain size is measured by X-ray powder diffraction (XRD). And the electric characteristics for NMOS, PMOS and polysilicon resistance are tested. Fig. 2 shows the poly resistance reduction proportion and poly grain size after anneal at 800oC, 900oC, and 1000oC for 5min, and 950oC for 20min in N2 ambient, respectively. Only after annealing at 950oC or above for 5min, the resistance can be obviously reduced, due to the poly grain size increasing. Fig. 3 shows threshold voltages (Vt) variation proportions of NMOS and PMOS owning gate length of 65nm and width 0.12µm after utilizing annealing process at different temperatures. PMOS is more sensitive to the anneal process than NMOS. But after anneal at 950oC or below, the threshold variation for both NMOS and PMOS is less than 5%, which is acceptable for the integration process manufacturing. A new anneal process at N2 ambient to adjust the polysilicon resistance has been proposed. It has been verified that utilizing anneal process at 950oC or below, the 65nm MOS performances can be maintained almost same as before. Consequently, it is considered that the anneal method can be to be applied to the deep submicron integration process. References [1] C. D. Parikh, and R. M. Patrikar, Solid-state Electronics, 43, 683 (1999). [2] R. Murii, and M. J. Deen,, IEEE Trans. Electron Devices, 49, 187 (2002). [3] C. Uang, H. Chuang, S. Tsai, K. Thei, P. Lai, S. Fu, Y. Tsai, W. Liu, IWJT, 293 (2004). [4] S. Gupta, J. Electrochem. Soc. 149, G271 (2002). [5] R. H. Dennard, F. J. Gasensslen, H. M. Yu, V. L. Rideout, E. Bassous, A. R. Leblanc, Solid-state Circuits Soc Mag. IEEE, 87, 668 (1999). Figure 1

Laterally Actuated Platinum-Coated Polysilicon NEM Relays

Integrated 4-terminal single-contact nanoelectromechanical relays implemented in a silicon-on-insulator foundry process

Enhanced Field-Dependent Conductivity and Material Properties of Nano-Aln/micro-sic/silicone Elastomer Hybrid Composites for Electric Stress Mitigation in High-Voltage Power Modules

Novel Materials Solutions And Simulations For Nanoelectromechanical Switches

A Highly Reliable Lateral MEMS Switch Utilizing Undoped Polysilicon As Isolation Material

Polymer Coating Enabled Carrier Modulation for Single-Walled Carbon Nanotube Network Inverters and Antiambipolar Transistors

Developing A Well-Adhered Ni/P Alloy Film On The Surface Of Silicone Elastomer For Shielding Electromagnetic Interferences

Toward Monolithically Integrated Hybrid CMOS-NEM Circuits

A Robust Polysilicon-Assisted SCR in ESD Protection Application

Sub-0.3 volt amorphous metal WNx based NEMS switch with 8 trillion cycles

Bulk Micromachined Relay with Lateral Contact

Robust Silicon Carbide (sic) Nanoelectromechanical Switches with Long Cycles in Ambient and High Temperature Conditions

Dual-gate Silicon Carbide (sic) Lateral Nanoelectromechanical Switches

A Low-Voltage Lateral MEMS Switch with High RF Performance

A Bulk Micromachined Relay with Lateral Contact and Isolation Structure

Piezoelectric SPDT NEMS Switch for Complementary Logic

Carbon-Carbon Contacts for Robust Nanoelectromechanical Switches

Electrodynamic Force, Casimir Effect, and Stiction Mitigation in Silicon Carbide Nanoelectromechanical Switches.

Wafer‐Scale CMOS‐Compatible Electro‐Thermally Actuated Nanomechanical Non‐Volatile Switch with Out‐of‐Plane Electrode Configuration

Laterally Actuated Si-to-Si DC MEMS Switch for Power Switching Applications

Thermal Method to Reduce the Polysilicon Resistance for Deep Submicron Integration Process