Abstract:Microelectromechanical system (MEMS)-based devices have gained attention recently due to their beneficial biomedical applications. MEMS-based devices like microneedles have set new trends in drug delivery, vaccination, skin, and eye treatment. Different materials like metals, sugars, polymers, and silicon have been used for fabrication. Various techniques have been used for their fabrication, including laser ablation, lithography, injection molding, and additive manufacturing. The tip diameter of different micron ranges has been achieved. The strength and stiffness of the microneedle's tip have always been important in fabricating microneedles so that it does not break on insertion. This research paper presents a comparison between silver (Ag) and copper (Cu) solid microneedles by performing numerical analysis using the fuzzy approach, structural simulation, and fabrication. Firstly, structural simulation has been performed in ANSYS software to test the strength of silver (Ag) and copper (Cu) microneedles separately. The purpose is to compare the stress effect and fracture limit of both microneedles. The results collected from the simulation provide valuable target and prediction facts to fabricate improved designs of the solid Ag and Cu microneedles. Then, fuzzy-based numerical analysis has been performed in MATLAB software for both microneedles separately. In this numerical analysis, the effect on the range of microneedle tip diameter and cone length has been observed by varying input voltage and time. Finally, fabrication has been performed using a novel economical technique such as electrochemical etching. Electrochemical etching is a very low-cost and clean room-free technique as compared to other techniques used for the fabrication of microneedles. The fabrication technique adopted in this work is the same for both silver and copper microneedles. The scanning electron microscopy (SEM) characterization has been performed for both fabricated microneedle tips. The tip of the fabricated solid Ag and Cu microneedle has been then coated with drugs using the dip-coating method. The coated solid Ag and Cu microneedle's tip has been then characterized again using SEM. The numerical results calculated from the fuzzy analysis have been then compared with fabrication results. The fuzzy analysis gives the simulated size of the microneedle's tip for 5.05 μm silver and 5.12 μm copper which have very close approximation with the experimental values from the SEM micrographs which also give the values of the cone length from 400 to 500 μm and the tip size from 5 to 6 μm for the time of 10–15 minutes, whose values were optimized by the fuzzy analysis. The results of this research provide valuable benchmark and prediction data to fabricate improved designs of the silver solid microneedles for drug delivery and other biomedical applications.

Design, modeling and simulation of MEMS-based silicon Microneedles

Design, Development, and Testing of Polymeric Microblades: A Novel Design of Microneedles for Biomedical Applications

In-Plane Si Microneedles: Fabrication, Characterization, Modeling and Applications

DESIGN, SIMULATION AND ANALYSIS OF MICRONEEDLES FOR TRANSDERMAL DRUG DELIVERY

Numerical Simulation, Analysis, and Fabrication of MEMS-Based Solid Ag and Cu Microneedles for Biomedical Applications

Geometrical effects in mechanical characterizing of microneedle for biomedical applications

Application of MEMS Microneedles Array in Biomedicine

Microfabricated Polysilicon Microneedles for Minimally Invasive Biomedical Devices

Effect of hollow microneedle geometry structure on mechanical stability and microfluidic flow for transdermal drug delivery applications

Xenon Difluoride Dry Etching for the Microfabrication of Solid Microneedles as a Potential Strategy in Transdermal Drug Delivery

Modeling of Microneedle Arrays in Transdermal Drug Delivery Applications

Insights into the mechanics of solid conical microneedle array insertion into skin using the finite element method

Design of three-section microneedle towards low insertion force and high drug delivery amount using the finite element method

Simulation assisted design for microneedle manufacturing: Computational modeling of two-photon templated electrodeposition

An Improved Manufacturing Approach for Discrete Silicon Microneedle Arrays with Tunable Height-Pitch Ratio.

A Novel Fabrication Method of Silicon Nano-Needles Using Mems Tmah Etching Techniques

The Finite Element Analysis Research on Microneedle Design Strategy and Transdermal Drug Delivery System

Finite Element Analysis of Skin Deformation and Puncture for Microneedle Array Design

Silica Needle Template Fabrication of Metal Hollow Microneedle Arrays

Fabrication of densely arrayed micro-needles with flow channels by mechanical dicing and anisotropic wet etching

3D Polymeric Lattice Microstructure‐Based Microneedle Array for Transdermal Electrochemical Biosensing