Abstract:Carbon/polymer binder composite bipolar plates for proton exchange membrane fuel cells have attracted attention for their corrosion resistivity and ease of manufacturing. However, the hot-pressing fabrication process often leads to a resin-rich surface on the plate, which may increase the interfacial contact resistance. A number of studies have been reported to reduce resin accumulation on the surface. However, most reported methods have focused on how to exceed the United States Department of Energy conductivity and mechanical targets. Their fabrication methods are often complicated, which is hard to form flow channels directly in manufacturing. Herein, we propose a simple layer-by-layer method to prepare graphite/resin composite bipolar plates. During compression of the multilayer graphite/resin powder, elevated temperature and pressure make the resin in the inner polymer-rich layer flow toward the outer resin-deficient layers. Scanning electron microscopy with energy-dispersive X-ray analysis shows an unbroken “smiling” curve of carbon content along the whole cross-section, suggesting a continuous distribution of the resin across the whole composite. The resulting composite demonstrates a better interfacial contact resistance (9.2 mΩ cm2@100 psi) and a flexural strength (44.3 MPa) than the plates prepared by a single-layer method. Flow channels with a good molding accuracy (±4 μm) are also observed. Single-cell testing with the gradient-structured composite plate shows excellent cell performance: the cell voltage is 0.67 V at 1 A cm–2, and the maximum power density reaches 0.99 W cm–2. In situ electrochemical impedance analysis demonstrates that compared to an analogue using the single-layer loading method, the cell with gradient structured plates displays lower ohmic and mass transfer resistance than the cell using the plates prepared by a single-layer method.

Low‐cost graphite coated copper as bipolar plates of proton exchange membrane fuel cells for corrosion protection

Novel Graphite Paper/Cu-Coated Magnesium as Bipolar Plates for Ultra-lightweight Proton Exchange Membrane Fuel Cells

Gold-Reduced Graphene Oxide Composite Coating on Stainless Steel 316L As Bipolar Plate for Proton Exchange Membrane Fuel Cell

Durable corrosion-resistant coating based in graphene oxide for cost-effective fuel cells components

Enhanced Anticorrosion Performance of PPY-graphene Oxide/ppy-Camphorsulfonic Acid Composite Coating for 304SS Bipolar Plates in Proton Exchange Membrane Fuel Cell

Hydrophobic octadecylamine-functionalized graphene/TiO2 hybrid coating for corrosion protection of copper bipolar plates in simulated proton exchange membrane fuel cell environment

High corrosion resistance of reduced graphene oxide coated 316L stainless steel bipolar plate for proton exchange membrane fuel cell prepared by a facile method

Significant Enhancement of Corrosion Resistance of Stainless Steel with Nanostructured Carbon Coatings by Substrate-Catalytic CVD

Superior conducting polypyrrole anti-corrosion coating containing functionalized carbon powders for 304 stainless steel bipolar plates in proton exchange membrane fuel cells

Graphene-Dominated Hybrid Coatings with Highly Compacted Structure on Stainless Steel Bipolar Plates

Polyvinyl Alcohol Anion Exchange Resin Composite Membrane with Co@Cu Core–Shell Particles for Direct Borohydride Fuel Cell Applications

The Effects of Molybdenum and Reduced Graphene Oxide on Corrosion Resistance of Amorphous Nickel–phosphorus As Bipolar Plates in PEMFC Environment

A novel high corrosion-resistant polytetrafluoroethylene/carbon cloth/Ag coating on magnesium alloys as bipolar plates for light-weight proton exchange membrane fuel cells

Graphene composite coating for enhanced corrosion resistance of Ni foam flow field in PEMFC

Preparation and Performance Study of PEK‐C‐OH/MWCNT‐COOH/Graphite Composite Bipolar Plates for PEMFCs With Improved Interface Properties

Protective coatings for metal bipolar plates of fuel cells: A review

Atmospheric plasma deposition of conductive and corrosion‐resistant composite coatings for proton exchange membrane fuel cell bipolar plates

Gradient Structured Composite Bipolar Plates for Proton Exchange Membrane Fuel Cells

Electrochemical Performance Testing and Characterization of Silver-Plated and Graphite-Coated 316l Stainless Steel Bipolar Plates

Corrosion Resistant, Lightweight, and Inexpensive Metallic Bipolar Plates With Excellent Manufacturability for PEM Fuel Cell Power Systems

Reducing Irreversible Performance Losses via a Graphene Oxide Buffer Layer for Proton-Exchange Membrane Fuel Cells