Abstract:Carbon/polymer binder composite bipolar plates for proton exchange membrane fuel cells have attracted attention for their corrosion resistivity and ease of manufacturing. However, the hot-pressing fabrication process often leads to a resin-rich surface on the plate, which may increase the interfacial contact resistance. A number of studies have been reported to reduce resin accumulation on the surface. However, most reported methods have focused on how to exceed the United States Department of Energy conductivity and mechanical targets. Their fabrication methods are often complicated, which is hard to form flow channels directly in manufacturing. Herein, we propose a simple layer-by-layer method to prepare graphite/resin composite bipolar plates. During compression of the multilayer graphite/resin powder, elevated temperature and pressure make the resin in the inner polymer-rich layer flow toward the outer resin-deficient layers. Scanning electron microscopy with energy-dispersive X-ray analysis shows an unbroken “smiling” curve of carbon content along the whole cross-section, suggesting a continuous distribution of the resin across the whole composite. The resulting composite demonstrates a better interfacial contact resistance (9.2 mΩ cm2@100 psi) and a flexural strength (44.3 MPa) than the plates prepared by a single-layer method. Flow channels with a good molding accuracy (±4 μm) are also observed. Single-cell testing with the gradient-structured composite plate shows excellent cell performance: the cell voltage is 0.67 V at 1 A cm–2, and the maximum power density reaches 0.99 W cm–2. In situ electrochemical impedance analysis demonstrates that compared to an analogue using the single-layer loading method, the cell with gradient structured plates displays lower ohmic and mass transfer resistance than the cell using the plates prepared by a single-layer method.

Corrosion Resistant, Lightweight, and Inexpensive Metallic Bipolar Plates With Excellent Manufacturability for PEM Fuel Cell Power Systems

The Corrosion Resistance Behaviors of Metallic Bipolar Plates for PEMFC Coated with Physical Vapor Deposition (PVD): An Experimental Study

Carbon/Carbon Composite Bipolar Plate for Proton Exchange Membrane Fuel Cells

Investigation of PVD coating on corrosion resistance of metallic bipolar plates in PEM fuel cell

Bipolar plate design and fabrication using graphite reinforced composite laminate for proton exchange membrane fuel cells

Electrochemical Performance Testing and Characterization of Silver-Plated and Graphite-Coated 316l Stainless Steel Bipolar Plates

Optimization of Fuel Cell Performance Using Computational Fluid Dynamics

Effect of Bipolar Plate Material on Proton Exchange Membrane Fuel Cell Performance

Carbon Coated Stainless Steel Bipolar Plates in Polymer Electrolyte Membrane Fuel Cells

Metallic Material Selection and Prospective Surface Treatments for Proton Exchange Membrane Fuel Cell Bipolar Plates—A Review

Researches on the MCMB/Graphite Composite for Bipolar Plate in Fuel Cell

Analysis of the Corrosion Behavior of Al Alloy Bipolar Plate for Proton Exchange Membrane Fuel Cell (PEMFC) Under Operating Thermal Conditions

Performance of a Proton Exchange Membrane Fuel Cell Stack Using Conductive Amorphous Carbon-Coated 304 Stainless Steel Bipolar Plates

Preparation and properties of high performance nanocomposite bipolar plate for fuel cell

PERFORMANCE ANALYSIS OF A BIPOLAR PLATE IN A FUEL CELL USING COMPUTER FLUID DYNAMICS STUDIES

Cheap and stable bipolar plates

Corrosion Resistant Al‐Cr‐Mo Alloy Coating on Type 316L Stainless Steel Bipolar Plates for Proton Exchange Membrane Fuel Cell Applications

Probing the Corrosion Rates of Novel Titanium Substrates in a Simulated PEM Fuel Cell Environment

Fabrication of Metallic Bipolar Plates for Proton Exchange Membrane Fuel Cell by Flexible Forming Process-Numerical Simulations and Experiments

Gradient Structured Composite Bipolar Plates for Proton Exchange Membrane Fuel Cells

Research Progress and Prospects of Bipolar Plate Materials for Proton Exchange Membrane Fuel Cells