Abstract:One of the renewable energy sources that is presently being developed in Indonesia is the technology that converts solar energy into electrical energy using solar cells or PV panels. The power output of a solar panel is influenced by several factors, including solar radiation intensity, panel surface temperature, shading, and the angle of solar incidence. One factor that can influence the efficiency of a solar panel is the temperature of the solar module. The efficiency of a solar panel decreases as its temperature increases. Installing a Peltier TEC1-12706 on a PV panel will have an impact on heat absorption on the surface of the PV panel, thereby optimizing the power output of the PV panel. This study utilizes three monocrystalline solar panels with a power rating of 50 Wp, which are installed under three conditions: the first solar panel without a Peltier device, the second solar panel with twenty Peltier devices connected in series beside the solar panel, and the third solar panel with twenty Peltier devices connected in series both beside and beneath the solar panel. The output of these solar panels is remotely monitored using IoT as a connection to facilitate the monitoring and control of measured variables, including ambient temperature, solar panel surface temperature, voltage, current, solar panel output power, and efficiency. The data is collected at a height of approximately 12 meters in an outdoor laboratory at the Telecommunications Department of the Electrical Engineering Polytechnic of Sriwijaya Palembang. The measurements are collected between approximately 07:00 to 17:00 local time. The research results reveal that the monocrystalline PV panel with Peltier devices connected in series beneath and beside the solar panel has a higher absorption temperature compared to the solar panel without a Peltier device. Irradiance and ambient temperature have an influence on the voltage and current of the PV panel. The measured irradiance is directly influenced by the ambient temperature. The PV panel, with the addition of Peltier devices beneath and beside it, has an output voltage of 0.3 volts, a higher current value of 0.37 amperes, an increase in output power of 8.9 watts, and an overall average efficiency enhancement of 32.6% compared to the PV panel without a Peltier device.

Impact of the type, orientation, and temperature of solar panels on observed efficiency in Latvian climate conditions

Impact of Temperature on the Efficiency of Monocrystalline and Polycrystalline Photovoltaic Panels: A Comprehensive Experimental Analysis for Sustainable Energy Solutions

The effect of building integration on the temperature and performance of photovoltaic modules

Study of the second-generation of CdTe and CIGS thin film PV modules under natural sunlight conditions

Evaluation of the Impact of Temperature on the Performance of Photovoltaic Solar Panels Installed on Various Roofing Sheets

Study of Temperature Coefficients for Parameters of Photovoltaic Cells

EFFECTS OF THE TEMPERATURE ON THE OUTPUT VOLTAGE OF MONO-CRYSTALLINE AND POLY-CRYSTALLINE SOLAR PANELS

ANALYSIS OF RESEARCH ON THE INFLUENCE OF TEMPERATURE ON THE DEGRADATION AND EFFICIENCY OF SOLAR PANELS

Energy performance of commercial c-Si PV modules in accordance with IEC 61853-1, -2 and impact on the annual specific yield

Performance comparison of mono and polycrystalline silicon solar photovoltaic modules under tropical wet and dry climatic conditions in east-central India

Improving the efficiency of solar photovoltaics by means of geothermal cooling: A year-long test campaign

Comparative Performance Analysis of Grid-Connected PV Power Systems with Different PV Technologies in the Hot Summer and Cold Winter Zone

Performance evaluation of a solar photovoltaic system

Performance of photovoltaic panels with different inclinations under uniform thermal loading

An Assessment of a Photovoltaic System's Performance Based on the Measurements of Electric Parameters under Changing External Conditions

Simulation and Experimental Results for Energy Production Using Hybrid Photovoltaic Thermal Technology

The Impact of Ambient Weather Conditions and Energy Usage Patterns on the Performance of a Domestic Off-Grid Photovoltaic System

The Effect of Azimuth and Tilt Angle Changes on the Energy Balance of Photovoltaic System Installed in the Southern Slovakia Region

Solar Panel Optimization Using Peltier Module TEC1-12706

An Experimental and Numerical Investigation of Photovoltaic Module Temperature Under Varying Environmental Conditions

How the morning-afternoon cloudiness asymmetry affects the energy-maximizing azimuth direction of fixed-tilt monofacial solar panels