Abstract:Nomex honeycomb composite (NHC) has been increasingly used in the automotive, aerospace and defence applications due to its excellent thermal and mechanical properties. Its complex cellular hexagonal thin-walled configuration along with heterogeneous, soft and brittle nature pose substantial processing defects such as burr formation, tearing of walls, surface roughness, dimensional inaccuracy and low machining quality during conventional machining (CM). These surface defects have a substantial influence on the operating life and functional performance of its sandwiched structural members. Hybrid ultrasonic vibration assisted machining (HUSVAM) technology has been introduced to overcome such limitations. For an in depth research on HUSVAM of NHC using ultrasonic toothed disc cutter (UTDC), three dimensional finite element model was developed and experimental validation was carried out. The numerical simulation and experimental results were found to be in good agreement with one another. The influence of various machining parameters including the ultrasonic tool vibration amplitude (UTVA), feed rate (FR), depth of cut (DoC) and spindle angular speed (SAS) on NHC cutting forces, chip formation and surface quality was investigated using both HUSVAM and CM techniques. Furthermore, stresses, deformation and forces near tool-workpiece interaction along with the surface topography and morphologies were also analysed and compared for various operating conditions. A reduction in the cutting forces was found with the increase of SAS and UTVA (up to 65.47 % and 65.74 %, respectively). Although, the cutting forces were observed to increase by increasing the DoC and FR (up to 159.45 % and 126.33 %, respectively). DoC has a greater impact on the cutting forces among all machining parameters according to 4 levels, 4 factors (L16) orthogonal experiments based on Taguchi method. The results show that the chip formation and machining quality of NHC core can be improved with HUSVAM technique using UTDC. HUSVAM also reduced the cutting forces (up to 73 %) compared to CM. The ultrasonic toothed disc cutter generated large number of burr with very short length, no tearing defects and no uncut fibers as observed from scanning electron microscopy of NHC hexagonal cell structure, walls and triple points. A burr formation of less than 10 % was realized during HUSVAM of NHC cores for Fx≤3N, while it was found up to 20 % if Fx>3N, compared to at least 40 % during CM. The finite element model developed can be used to investigate the influence of HUSVAM on modern difficult to machine materials for enhanced surface quality.

Horn failure prediction in presence of internal defect in ultrasonic machining process through numerical investigation

Horn design and analysis in ultrasonic machining process using ANSYS

Tubular Bezier Horn Optimum Design for Ultrasonic Vibration Assisted Machining of Nomex Composite

Numerical Evaluation of State of the Art Horn Designs for Rotary Ultrasonic Vibration Assisted Machining of Nomex Honeycomb Composite

Harmonic Excitation Response of Standard Ultrasonic Horn Designs for Machining Nomex Honeycomb Core Composite

Numerical Investigation of the Effect of Uniform Cutout on Performance of Ultrasonic Horn for Machining Nomex Honeycomb Core Material

Dynamic Performance Evaluation of Ultrasonic Composite Horn for Machining Soft and Brittle Composites

Design and Analysis of Acoustic Horn for Assistance in Die-Sinking EDM

Milling Error Prediction of Thin-Walled Parts During High-Speed Machining

Ptimum Design of Acoustic Horns with Tool for Ultrasonic Machining Using Finite-Element Analysis

Design of Ultrasonic Machining Device for Thin-Wall Cylinder of Air Compressor

Design and finite element analysis of longitudinal vibrating stepped ultrasonic horn

Longitudinal–Torsional Frequency Coupling Design of Novel Ultrasonic Horns for Giant Magnetostrictive Transducers

Design and Development of Sonotrode for Ultrasonic Drilling

Machine learning coupled with acoustic emission signal features for tool wear estimation during ultrasonic machining of Inconel 718

Design and Experimental Study of Longitudinal-Torsional Composite Ultrasonic Internal Grinding Horn

Implementation of new stepped horn in rotary ultrasonic machining of NOMEX honeycomb composites

Design and optimization of two-section ultrasonic stepped horn

Investigation of hybrid ultrasonic machining process of Nomex honeycomb composite using a toothed disc cutter

Subsurface damage detection and prediction of thin-walled complex curved-surface component

Frequency coupling design of ultrasonic horn with spiral slots and performance analysis of longitudinal-torsional machining characteristics