Abstract:The design of tooling for ultrasonic machine is critical for every application. For the proper concentration of energy across the workpiece during ultrasonic machining, geometry of sonotrode plays important role. The entire ultrasonic assembly has to be tuned to the same frequency for transfer of maximum energy. If the natural or resonant frequency of the components in the ultrasonic assembly are different, it would set up vibrations of different frequencies leading to energy loss and even damage to certain components by fatigue at the interface surfaces. The issues involved in sonotrode design are material, shape, frequency, resonant length and gain. Proper design of sonotrode is essential to bridge the gap between the booster and the work surface and amplify the vibration amplitude to a value required for successful machining. The separate design of tool which can be assembled at the end of the sonotrode leads to acoustic coupling problems at that interface and separate design of sonotrode and tool and individual testing for successful tuning on the machine. It increases the possibility of failure also. For these reasons, the integrated design of sonotrode with tool being formed at the bottom end of sonotrode is preferred. The tool edge is so designed that only the periphery of the hole is to be cut to obtain through drilling. This reduces the amount of material to be removed and the machining time. The manual design procedure would require solving a second order partial differential equation with the boundary conditions applicable to the machine and the gain required. This paper discusses design of conical, exponential and step-cylindrical horn for ultrasonic machining. First the dimensions are obtained through commercial sonotrode design software CARD (Computer Aided Resonator Design). The software uses the finite difference theory for discretising the sonotrode along the length and iteratively finds the length for resonance condition with gain close to the required amplification provided by the user. It also gives the nodal point, anti-nodal point, stress variation and amplitude variation along the axis of the sonotrode over the entire length. End diameter and resonant length calculated from CARD are supplied to ANSYS to perform modal analysis. A good agreement is observed between the results obtained using CARD software and ANSYS. Based on this design, actual horn of the conical design is manufactured and tested on the machine for resonant frequency and the results are found to be close to those observed from CARD and ANSYS both.

Design and optimization of two-section ultrasonic stepped horn

Design and optimization of stepped compound horn based on finite element method

Design and finite element analysis of longitudinal vibrating stepped ultrasonic horn

Optimization research of stator with two degree-of-freedom traveling-wave spherical ultrasonic motor

Modeling and Optimal Design of the Rotary-Linear Type Two-Degree-of-Freedom Ultrasonic Motors

Ptimum Design of Acoustic Horns with Tool for Ultrasonic Machining Using Finite-Element Analysis

Optimization of ultrasonic transducer horn geometry with vibrational-thermal performance improvement approach

Design and experimental investigation of stepped horn with a hollow part to allow individual design of amplitude amplification factors for longitudinal-torsional vibration source

Study on multi-frequency characteristics of a longitudinal ultrasonic transducer with stepped horn

Design and Analysis of Ultrasonic Composite Transducer with a Quarter-wave Taper Transition Horn

Optimal Design of A Rod Shape Ultrasonic Motor Using Sequential Quadratic Programming and Finite Element Method

A Design of Silicon Based Horn Antenna Optimized Using Bayesian Optimization

Design and Development of Sonotrode for Ultrasonic Drilling

Design and Experimental Study of Longitudinal-Torsional Composite Ultrasonic Internal Grinding Horn

Design and Characterization of Ultrasonic Langevin Transducer 20 kHz Using a Stepped Horn Front-Mass

Numerical Evaluation of State of the Art Horn Designs for Rotary Ultrasonic Vibration Assisted Machining of Nomex Honeycomb Composite

Design of Ultrasonic Transducer with a Quarter Wavelength Composite Exponential Horn

Intelligent Optimization Design of a Phononic Crystal Air-Coupled Ultrasound Transducer

Horn design and analysis in ultrasonic machining process using ANSYS

Tubular Bezier Horn Optimum Design for Ultrasonic Vibration Assisted Machining of Nomex Composite

Design Optimization of a Dual Function Piezoelectric Actuator