Abstract:The present study investigated influences of the Al3Sc particle content on the evolution of bimodal grain structure and mechanical properties at both room and elevated temperatures of Al–7Mg–Sc alloys processed by hard-plate rolling (HPR). Bimodal grain structures were obtained in HPRed Al–7Mg–Sc alloys where ultrafine/fine grains decreased in size and increased in amount with increasing volume fraction of Al3Sc precipitates. The formation and evolution of bimodal grain structure are associated with (i) the different stability of various-orientated grains, and (ii) the volume fraction of Al3Sc precipitates. Ultrafine/fine (sub) grains form preferentially along grain boundaries (GBs) of <001>//normal direction (ND)- and <111>//ND-oriented coarse grains during HPR. In contrast, the <101>//ND-oriented coarse grains show relatively high stability nearly without subdivision. Furthermore, increased volume fraction of Al3Sc precipitates in Al–7Mg–0.4Sc promotes dislocation accumulation, favoring recrystallization nucleation, and meanwhile restricts grain growth, which results in more and refined ultrafine/fine grains. Thereby, the refined grain structure and increased volume fraction of Al3Sc precipitates in the Al–7Mg–0.4Sc alloy contribute to improved room-temperature yield strength (YS) and elongation, i.e. ~482 MPa and ~8%, which is much higher than that of ~420 MPa and ~4% in the binary Al–7Mg alloy. Meanwhile, Al–7Mg–0.4Sc exhibited higher hardness when annealed at 150–300 °C and also higher YS when subjected to a tensile test at ≤ 200 °C due to the more stabilized grain structure pinned by dispersed Al3Sc and additional strengthening effect from Al3Sc precipitates. Nevertheless, when subjected to a tensile test at ≥ 250 °C, the Al–7Mg–0.4Sc alloy exhibited much lower YS than binary Al–7Mg. The transition could be explained by more favored grain boundary sliding (GBS) and great dislocation loss, due to the easier occurrence of dynamic recrystallization (DRX) in Al–7Mg–0.4Sc during tensile test at elevated temperatures.

Microstructure and properties of extruded Al–Li–Cr alloy prepared from atomised powder

Microstructure Evolution and Properties of Mg-9Gd-0.8Al Alloy with Lamellar Phase During Extrusion at Different Temperatures

Microstructural evolution and mechanical properties of the rapidly-solidified and hot-extruded 2196 Al-Li alloy

Microstructures and Mechanical Properties of a L12-structured Precipitation Strengthened Co-based Superalloy

Microstructures and mechanical properties of high strength Ti-XAl-2Fe-3Cu alloys fabricated by powder compact extrusion

Tensile properties and fracture toughness of TiAl alloys with controlled microstructures

Changes in microstructure and mechanical properties of 2219 Al alloy during hot extrusion and post-extrusion aging

Microstructure, tensile properties and fracture behaviour of an Al-Cu-Li-Mg-Zr alloy 8090

Microstructural Evolution in a 6060 Extrudable Al-Alloy: Integrated Modeling and Experimental Validation

Influences of the Al3Sc particle content on the evolution of bimodal grain structure and mechanical properties of Al–Mg–Sc alloys processed by hard-plate rolling

Microstructure Evolution and Mechanical Properties of AZ80 Mg Alloy during Annular Channel Angular Extrusion Process and Heat Treatment

The Microstructure and tensile properties of a splat-quenched Al-Cu-Li-Mg-Zr alloy

Effects of extrusion on the microstructure and mechanical properties of Mg–Zn–Gd alloy reinforced with quasicrystalline particles

Development of ultrahigh-strength low-alloy Mg-0.7Al-0.3Ca-0.4Mn (wt.%) alloy with excellent ductility via controlling extrusion temperature

Study on the microstructure and mechanical properties of Mg–Al–Li–Zn–Ti multi-component alloy

Microstructural evolution and superplasticity of Al-5.8Mg-0.23Mn alloys processed by reciprocating extrusion

Microstructure and mechanical properties of Al−Mg−Si alloy U-shaped profile

Influence of Extrusion Temperature on Microstructure and Mechanical Properties of Mg-4Y-4Sm-0.5Zr Alloy

Effect of extrusion temperatures on the microstructures, mechanical properties and thermal properties of PM Al-20Si alloy

Microstructure and mechanical properties of Mg-Gd-Zn-Zr alloy after hot extrusion

Hot deformation behavior and microstructure characteristic of 2055 Al-Li alloy during uniaxial compression