Abstract:Square wave alternating current (AC) tungsten inert gas (TIG) welding possesses great advantages in welding stability, quality, flexibility, and cost in manufacturing thin-walled propellant storage tanks with 2219-T6 aluminum alloy. To solve the welding engineering problem of 4 mm-thick plates made by square wave AC TIG welding, we conducted process optimization experiments and performed common microstructure analysis and mechanical property testing. Tensile strength and microhardness reaching 63.8 and 83.1% of the base material appear in the optimal weld. The dendrite morphology, grain size, and eutectic content of all welds were compared and analyzed with optical microscopic observation, image segmentation, and grayscale statistics. The obtained quantitative results interpret the macroscopic properties of the optimal weld from a microscopic perspective. Shallow and uniform equiaxed dimples, evident tearing ridges, and second-phase particles were detected in the tensile fractures. Reticular, granular, and lath eutectic ( α (Al) + CuAl 2 ) were found in the interior and boundaries of dendritic solid solution ( α (Al)). Unexpectedly, the epitaxial growth of the columnar grains was inconspicuous or absent in all welds. Uniform and fine equiaxed grains occupy almost all welds of different process parameters, while the G/R ratio of these welds reaches 15-23 °C·s/mm^2, under which the equiaxed crystals should not have formed. We attributed the grain refinement in these welds to the secondary phase particles in base metal. They are broken into fragments during the multi-pass rolling process of plates, remain semi-dissolved under a fast cooling rate, and provide adequate heterogeneous nuclei for melt solidification. A further SEM and EDS test to base metal and secondary phase particles confirmed our findings and speculations. These results suggest that in the molten pool with sufficient heterogeneous nucleation, the mechanical blocking effect of heterogeneous nucleation may interfere with the thermodynamic effect of welding heat input and speed on grain structure.

Effect of Alloying Composition on Microstructure and Mechanical Properties of Ultranarrow Gap Welded Joints of U71Mn Rail Steel

The sensitivity analysis of microstructure and mechanical properties to welding parameters for linear friction welded rail steel joints

Study on microstructure and mechanical properties of continuous drive friction-welded joints of bainitic rail steel

Influence of CDFW Process Parameters on Microstructure and Mechanical Properties of U75V Rail Steel Welded Joint

Improving the microstructures and mechanical properties of U71Mn rail steel liner friction welded joint by normalizing treatment

Microstructural Evolution and Micro-Corrosion Behaviour of Flash-Welded U71Mn Joints as a Function of Post-Weld Heat Treatment

Effect of Normalizing Temperature on Hardness and Microstructure of Rail Joints with Narrow-Gap Automatic Arc Welding

Effect on Hardness and Microstructures of Rail Joint with Narrow Gap Arc Welding by Normalizing

Novel Weld Composition to Improve Mechanical Properties of 2219-T8 Aluminum Alloy Joint Using Double-Wire TIG Welding

Comparison of Microstructure and Mechanical Properties of Ultra-Narrow Gap Metal Active Gas Arc Welded and Narrow Gap Submerged Arc Welded Q235A Low Carbon Steel

Quasi-equal Strength and Toughness Matching Rail Steel Joint Obtained Via Friction Welding below Ac1 Temperature

A comparative study of the microstructure and properties of 800 MPa microalloyed C-Mn steel welded joints by laser and gas metal arc welding

Microstructure Evolution and Mechanical Properties of Thick 2219 Aluminum Alloy Welded Joints by Electron-Beam Welding

Influence of Rail Metallurgy and Welding Parameterization on the Quality of Flash Butt Welds Done with Mobile Equipment

Mechanical and Tribological Behaviors of U75VG Rail Flash−Butt Welded Joint

The Microstructure and Mechanical Properties of Welded Joints of Hot-Rolled and Post-Weld Solution-Treated Fe-12.5Mn-9.8Al-1.0C Low-Density Steel

Influence of Heterogeneous Mechanical Properties on the Performance of Forward Static Bending Test of Rail Welded Joint

Research on Microstructure and Mechanical Properties of Square Wave Alternating Current Tungsten Inert Gas Welded Joints in 2219-T6 Aluminum Alloy

Microstructure evolution and mechanical properties in a gas tungsten arc welded Fe42Mn28Co10Cr15Si5 metastable high entropy alloy

Effect of Welding Speed on Microstructure and Mechanical Properties of 30CrMnSiNi2A Steel Electron Beam Welded Joint

Effect of CMT Welding Heat Input on Microstructure and Properties of 2A14 Aluminum Alloy Joint