Laser Prepared Thin Films for Optoelectronic Applications

Marcela Socol,Gabriel Socol,Nicoleta Preda,Anca Stanculescu and Florin Stanculescu,Florin Stanculescu,Anca Stanculescu

DOI: https://doi.org/10.5772/67659

2017-05-24

Abstract:Laser Prepared Thin Films for Optoelectronic Applications | InTechOpen, Published on: 2017-05-24. Authors: Marcela Socol, Gabriel Socol, Nicoleta Preda, et

What problem does this paper attempt to address?

Amorphous thin films for mechanically flexible, multimaterial integrated photonics

Lan Li,Hongtao Lin,Sarah Geiger,Aidan Zerdoum,Ping Zhang,Okechukwu Ogbuu,Qingyang Du,Xinqiao Jia,Spencer Novak,Charmayne Smith,Kathleen Richardson,J David Musgraves,Juejun Hu

2016-01-01

American ceramic society bulletin

Abstract:Flexible integrated photonics is a new technology which only started to burgeon in the past few years, opening up emerging applications ranging from flexible optical interconnects to conformal sensors on biological tissues. One of the most important factors dictating the performance of these flexible devices is the material choice. Organic polymers are generally considered to be compatible with flexible substrates. However, the low refractive indices of polymers (compared to semiconductors) cannot provide the strong optical confinement necessary for compact photonic integration. Besides polymers, semiconductor NanoMembranes (NMs), thin slices of single crystal semiconductors with sub-micron thickness, are being actively pursued for photonic device integration on flexible substrates. Unlike their rigid bulk counterparts, NMs can be tightly bent without cracking, since surface strain induced by bending linearly scales with the membrane thickness. To make photonic devices, NMs structures are usually first patterned on a rigid substrate such as silicon. The fabricated structures are then picked up by a PDMS rubber stamp and transferred on to the final flexible substrate.This multi-step hybrid process limits processing yield and throughput. Therefore, we turned to amorphous glasses – the material of choice for optics given their exceptionally low optical attenuation. In flexible photonics, using these non-crystalline materials also enables a monolithic fabrication route as they can be directly deposited on to flexible substrates without resorting to epitaxial growth. Specifically, we focus on chalcogenide glass …
Thin Films of Metal-Organic Framework Interfaces Obtained by Laser Evaporation

Olivia L. Rose,Anca Bonciu,Valentina Marascu,Andreea Matei,Qian Liu,Laurentiu Rusen,Valentina Dinca,Cerasela Zoica Dinu

DOI: https://doi.org/10.3390/nano11061367

IF: 5.3

2021-05-21

Nanomaterials

Abstract:Properties such as large surface area, high pore volume, high chemical and thermal stability, and structural flexibility render zeolitic imidazolate frameworks (ZIFs) well-suited materials for gas separation, chemical sensors, and optical and electrical devices. For such applications, film processing is a prerequisite. Herein, matrix-assisted pulsed laser evaporation (MAPLE) was successfully used as a single-step deposition process to fabricate ZIF-8 films. By correlating laser fluency and controlling the specific transfer of lab-synthesized ZIF-8, films with user-controlled physical and chemical properties were obtained. Films’ characteristics were evaluated by scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) spectroscopy, X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, and X-ray photoelectron spectroscopy (XPS). The analysis showed that frameworks of ZIF-8 can be deposited successfully and controllably to yield polycrystalline films. The deposited films maintained the integrity of the individual ZIF-8 framework, while undergoing minor crystalline and surface chemistry changes. No significant changes in particle size were observed. Our study demonstrated control over both the MAPLE deposition conditions and the outcome, as well as the suitability of the listed deposition method to create composite architectures that could potentially be used in applications ranging from selective membranes to gas sensors.

materials science, multidisciplinary,physics, applied,nanoscience & nanotechnology,chemistry
Laser Processing of Emerging Nanomaterials for Optoelectronics and Photocatalysis

Anna Lipovka,Aura Garcia,Elena Abyzova,Maxim Fatkullin,Ziyang Song,Yuxiang Li,Ranran Wang,Raul D. Rodriguez,Evgeniya Sheremet

DOI: https://doi.org/10.1002/adom.202303194

IF: 9

2024-04-04

Advanced Optical Materials

Abstract:This review focuses on the laser processing of MXenes, metal‐organic frameworks, and perovskites in optoelectronics and photocatalysis. It discusses the properties of these materials and their combinations, and thoughtfully summarizes laser‐assisted techniques to synthesize and modify emerging materials. Finally, it serves as a guide for researchers aiming to use lasers to enhance the materials' performance and revolutionize next‐generation optoelectronic devices. Optoelectronics and photocatalysis are two rapidly developing photonic fields that are revolutionizing green energy, medicine, communications, and robotics. To advance these areas and explore new applications, there is a need for new materials and technologies that enable fast, scalable, and customizable production of high‐performing optoelectronics, including the future development of flexible devices. This review is focused on the strategies to synthesize novel, not fully explored materials and/or enhance their properties using the powerful method of laser processing. The discussion includes the laser treatment of MXenes, Metal‐Organic Frameworks, and perovskites, materials' advantages in terms of structural, electronic, and optical properties, and the role of different laser‐based techniques in boosting their performance. Additionally, there is a demonstration of the existing and potential applications of these three materials and their combinations, especially in optoelectronics and photocatalytic platforms. This review aims to provide a comprehensive understanding of the current state‐of‐the‐art in this field to help researchers identify opportunities and challenges in laser processing of emerging nanomaterials for optoelectronics and photocatalysis.

materials science, multidisciplinary,optics
Laser Technology for Perovskite: Fabrication and Applications (Adv. Mater. Technol. 10/2024)

Zhengfen Wan,Zichen Liu,Qiwen Zhang,Qiming Zhang,Min Gu

DOI: https://doi.org/10.1002/admt.202470044

IF: 6.8

2024-05-23

Advanced Materials Technologies

Abstract:Laser Technology for Perovskite Laser technology offers a versatile and mask‐free method for fabricating, structuring, modifying, and patterning perovskites. It is employed to create perovskite quantum dots, nanowires, nanocrystals, and films. In article number 2302033, Min Gu and co‐workers study laser‐induced perovskites in glass for their exceptional stability. Multiple applications of perovskite, such as solar cells, LEDs, data storage, optical encryption, photodetection, and lithography, are reviewed.

materials science, multidisciplinary
Compressing High Energy Lasers through Optical Polymer Films

Jonathan Wheeler,Gabriel Petrişor Bleotu,Andrei Naziru,Riccardo Fabbri,Masruri Masruri,Radu Secareanu,Deano M. Farinella,Gabriel Cojocaru,Razvan Ungureanu,Elsa Baynard,Julien Demailly,Moana Pittman,Razvan Dabu,Ioan Dancus,Daniel Ursescu,David Ros,Toshiki Tajima,Gerard Mourou

DOI: https://doi.org/10.3390/photonics9100715

IF: 2.536

2022-10-01

Photonics

Abstract:The thin-film post-compression technique has the ability to reduce the pulse duration in PW-class lasers, increasing the peak power. Here, the nonlinear response of an increasingly available optical thermoplastic demonstrates enhanced spectral broadening, with corresponding shorter pulse duration compared to fused silica glass. The thermoplastic can be used close to its damage threshold when refreshed using a roller mechanism, and the total amount of material can be varied by folding the film. As a proof-of-principle demonstration scalable to 10-PW, a roller mechanism capable of up to 6 passes through a sub-millimeter thermoplastic film is used in vacuum to produce two-fold post-compression of the pulse. The compact design makes it an ideal method to further boost ultrahigh laser pulse intensities with benefits to many areas, including driving high energy acceleration.

optics
Photoablative Etching of Materials for Optoelectronic Integrated Devices

P LEMOINE,JD MAGAN,W BLAU

DOI: https://doi.org/10.1117/12.25023

1991-01-01

Abstract:Laser photoablation of a variety of polymer films was observed at UV wavelengths. The etch curves do not fit Beer's law and the Srinavasan model but follow the trend of a multiphotonic process. Ablation occurs with minimal degradation in the remaining material. Linear absorption characteristics and chemical composition are not the only factors which contribute to the etching mechanism. Process parameters also include mechanical properties, sample purity and microstructure.
Coprocessed heterogeneous near-infrared lasers on thin-film lithium niobate

Theodore Morin,Jon Peters,Mingxiao Li,Joel Guo,Yating Wan,Chao Xiang,John Bowers,Theodore J. Morin,Jonathan Peters,John E. Bowers

DOI: https://doi.org/10.1364/ol.516486

IF: 3.6

2024-02-23

Optics Letters

Abstract:Theodore J. Morin, Jonathan Peters, Mingxiao Li, Joel Guo, Yating Wan, Chao Xiang, John E. Bowers Thin-film lithium niobate (TFLN) is an attractive platform for photonic applications on account of its wide bandgap, its large ... [Opt. Lett. 49, 1197-1200 (2024)]

optics
Methodology of selective metallic thin film ablation from susceptible polymer substrate using pulsed femtosecond laser

Chresten von der Heide,Maria Grein,Günther Bräuer,Andreas Dietzel

DOI: https://doi.org/10.1364/OE.391084

2020-02-10

Abstract:Electronic devices are progressively fabricated on flexible substrates allowing new fields of applications. A maskless and very flexible structuring process is offered by ablation using ultra-short pulse laser irradiation. Usually, certain areas of a functional thin film coating are locally removed to yield the needed device structures. Micro laser patterning quality is not only influenced by the beam properties (beam profile, fluence) but also by pulse overlap, scan repetitions and many other factors such as substrate and coating material. This makes process parameter optimization a challenging task. In this paper, we present a systematic approach to efficiently find suitable parameters for laser-induced ablation of thin films on susceptible polymer substrates. As an example, we use a sputtered NiCr coating with a thickness of 100 $nm$ on a polyimide film made by spin coating of PI-2611 precursor (@ 2000 $rpm$ > ca. 8 ${\mu}m$, HD microsystems). Irradiation is conducted using a fs-laser with infrared wavelength of 1030 $nm$ and a pulse length of 212 $fs$. The energy per pulse is varied in the range of 0,29 ${\mu}J$ to 4,83 ${\mu}J$, yielding fluence values between 70 $mJ/cm^2$ and 1,11 $J/cm^2$. Ablation threshold fluence for a 100 $nm$ layer of NiCr was found to be ${\phi}_{th}$ ($N_P$:1)=0,50 $J/cm^2$ and the incubation factor was evaluated to be ${\xi}$=0,53. A clear distinction must be made between the material ablation at the surface of a bulk material and the selective removal of a thin film. In the second case effects such as flaking occur in practice and influence the ablation characteristic. We then investigate different varieties of thin film removal including dot-, line- and areal-ablation. The methodology is presented using a practical example, but can be applied to selective ablation of a wide range of thin film systems.

Applied Physics,Optics
Micro-/Nano-Structures Fabricated by Laser Technologies for Optoelectronic Devices

Jian Yi,Hao Zhou,Wei-Hua Wei,Xing-Chen Han,Dong-Dong Han,Bing-Rong Gao

DOI: https://doi.org/10.3389/fchem.2021.823715

IF: 5.5

2021-12-16

Frontiers in Chemistry

Abstract:Due to unique optical and electrical properties, micro-/nano-structures have become an essential part of optoelectronic devices. Here, we summarize the recent developments in micro-/nano-structures fabricated by laser technologies for optoelectronic devices. The fabrication of micro-/nano-structures by various laser technologies is reviewed. Micro-/nano-structures in optoelectronic devices for performance improvement are reviewed. In addition, typical optoelectronic devices with micro-nano structures are also summarized. Finally, the challenges and prospects are discussed.

chemistry, multidisciplinary
Investigation of laser-induced changes in structural and optoelectrical properties of pulsed laser-deposited Diamond-Like Carbon layers

R. Meyer,F. Stock,F. Antoni,F. Z. Lahboub,S. Hajjar-Garreau,D. Muller

DOI: https://doi.org/10.1007/s10854-023-10802-2

2023-06-18

Abstract:In the next years, one of the biggest challenges for optoelectronic devices will be the necessity to provide a suitable and reliable alternative to the use of transparent conducting oxide (TCO) like Indium Thin Oxide (ITO) as transparent electrodes. We recently demonstrated a promising fully laser-based method to produce transparent conductive electrodes only made of pure carbon materials. In a first step, we use the Pulsed Laser Deposition (PLD) to synthetize high performance Diamond-Like Carbon (DLC), an amorphous pure carbon material composed of a mixture of sp 2 (graphitic) sp 3 (diamond) hybridized carbon atoms. DLC thin films show very interesting properties comparable to those of diamond, like a high transparency in the visible range, high wear resistance, biocompatibility, chemical inertness and high electrical insulation. DLC also presents one particularity compared to diamond which its relative high opacity in the UV range. This feature is used in a second step to perform an UV laser surface treatment to graphitize the very first atomic layers of the DLC thin film. DLC opacity at treatment wavelength will help to restrict the laser interaction at the surface and will break dominant diamond bindings, allowing carbon atoms to reorganize into its stable form, forming by their way a Thin Graphitic Layer (TGL). Raman spectroscopy (RS) and X-ray Photoemission Spectroscopy (XPS) perform before and after laser annealing clearly demonstrate the DLC surface graphitization kinetic. Transmittance and surface conductivity measurement show very promising results and performances that can clearly compete with those of ITO. In addition to all these analyses, this pure laser process will be fully compatible with standard microelectronic technological steps and will have a low ecological footprint compared to other much heavier processes.

engineering, electrical & electronic,materials science, multidisciplinary,physics, condensed matter, applied
Biomolecular papain thin films growth by laser techniques

Enikö György,Jose Santiso,Albert Figueras,Gabriel Socol,Ion N Mihailescu

DOI: https://doi.org/10.1007/s10856-007-3055-0

Abstract:Papain thin films were synthesised by matrix assisted and conventional pulsed laser deposition (PLD) techniques. The targets submitted to laser radiation consisted on a frozen composite obtained by dissolving the biomaterials in distilled water. For the deposition of the thin films by conventional PLD pressed biomaterial powder targets were submitted to laser irradiation. An UV KrF* excimer laser source was used in the experiments at 0.5 J/cm(2) incident fluence value, diminished one order of magnitude as compared to irradiation of inorganic materials. The surface morphology of the obtained thin films was studied by atomic force profilometry and atomic force microscopy. The investigations showed that the growth mode and surface quality of the deposited biomaterial thin films is strongly influenced by the target preparation procedure.
Laser Micro-Fabrication/Manipulation of Dielectric Materials

H Misawa,S Juodkazis,A Marcinkevicius,V Mizeikis,A Yamaguchi,HB Sun,S Matsuo

DOI: https://doi.org/10.1109/mhs.2000.903278

2000-01-01

Abstract:We describe microfabrication of various materials by multiphoton absorption of femtosecond (120-150 fs) light pulses. The photo-modification at the focal point of tightly focused laser beam occurs inherently within a volume smaller than that defined by the diffraction limit. The achievable lateral resolution is compared with that obtainable by lithography which uses near-field optical microscopy. This technique can in principle lead to the realization of 3D optical memory and photonic crystals with arbitrary lattice in polymers and silica glass, 3D prototyping in polymerizable resins, and etching of 3D structures guided by the optically damaged pattern in silica. Another topic also discussed deals with laser micromanipulation using continuous wave laser operating at 1.06 /spl mu/m. Light-controlled revolution of liquid crystal droplet and volume-phase transition of gels are described.
LIPSS on thin metallic films: New insights from multiplicity of laser-excited electromagnetic modes and efficiency of metal oxidation

Alexander V. Dostovalov,Thibault J. -Y. Derrien,Sergei A. Lizunov,Filip Preucil,Konstantin A. Okotrub,Tomas Mocek,Victor P. Korolkov,Sergei A. Babin,Nadezhda M. Bulgakova,Thibault J.-Y. Derrien

DOI: https://doi.org/10.48550/arXiv.1910.07280

2019-10-16

Applied Physics

Abstract:Thin Cr films 28-nm thick deposited on glass substrates were processed by scanning low-intensity femtosecond laser pulses with energy well below single-pulse damage threshold. Two types of laser-induced periodic surface structures (LIPSS) were produced, depending on the scanning velocity, (1) parallel to laser light polarization with periodicity somewhat smaller than laser wavelength and (2) perpendicular to polarization with spatial period much smaller than wavelength. All structures are formed as protrusions above the initial film surface and exhibit a high degree of oxidation. To explain formation of the LIPSS and their conversion from one to another type, a rigorous numerical approach for modeling surface electromagnetic waves in thin-film geometry has been developed, which takes into account the change of optical properties of material due to laser-induced oxidation and porosity. The approach addresses the multiplicity of electromagnetic modes allowed for thin films. It has been found that the low spatial frequency LIPSS parallel to laser polarization, which are formed at low scanning velocities, are well described by the Sipe theory for surfaces of low roughness. The SEW mode responsible for high spatial frequency LIPSS formation at high scanning velocities has been identified. The mechanisms of optical feedback and transformation between types of LIPSS with scanning velocity have been proposed.
Laser-assisted two dimensional material electronic and optoelectronic devices

Bao-Wang Su,Xi-Lin Zhang,Wei Xin,Hao-Wei Guo,Yu-Zhe Zhang,Zhi-Bo Liu,Jian-Guo Tian

DOI: https://doi.org/10.1039/d0tc05540a

IF: 6.4

2021-01-01

Journal of Materials Chemistry C

Abstract:Laser processing techniques have been utilized to achieve high-performance 2D material electronic and optoelectronic devices. Herein, various 2D material electronic and optoelectronic devices fabricated via laser processing are reviewed.

materials science, multidisciplinary,physics, applied
Phenomenological studies of femtosecond laser ablation on optical thin films for integrated photonics

R. Peyton,V. Guarepi,G.A. Torchia

DOI: https://doi.org/10.1016/j.optlastec.2020.106059

2019-01-26

Abstract:In this work, for the first time of our knowledge, we present a well-supported procedure to fabricate ridge optical waveguides onto thin films of PLZT by femtosecond laser ablation. In order to achieve smooth guiding structures to guarantee good optical performance, we have studied the ablation threshold characteristics for different kinematic conditions of fs laser machining and also we have explored the different ablation regimens for several fluencies reached. Besides, we characterize the morphology and roughness of ridge waveguides through a modal and scattering loss analysis, for waveguides made with single and multiple scan. An innovative phenomenological model that relates the sidewall roughness to process parameters is proposed in this paper. Conducting this approach it is possible to extend the fabrication method of smooth guiding structures by fs micromachining to many optical thin films in order to develop integrated photonics devices addressed to different technological applications.

Applied Physics,Materials Science,Optics
A study of the possibility of conducting selective laser processing of thin composite electrochromic Ni(OH)2-PVA films

Valerii Kotok,Vadym Kovalenko

DOI: https://doi.org/10.15587/1729-4061.2021.225355

2021-02-26

Abstract:The surfaces of thin composite electrochromic Ni(OH)2-polyvinyl alcohol films, deposited by the cathodic template method on FTO glass substrates, were proposed to be processed using laser radiation. The processing of these films was carried out in a colored state with a laser beam of a semiconductor emitter with a wavelength of 650 nm (red) with a pulse duration of 3,000 μs, the beam diameter was about 40 μm. The energy at a single point was 37.5 J/cm2. The result was a film with microholes of about 80 μm. The transparent areas of the surface did not exhibit electrochromic properties, which indicated the absence of the original electrochromic coating. The study of the properties of the laser-processed film following a certain pattern showed that the characteristics of composite Ni(OH)2-polyvinyl alcohol coatings had changed significantly. On the one hand, the coloration depth of the films decreased by several percent, on the other hand, the specific electrochemical characteristics increased significantly. The study also showed that laser processing did not lead to significant changes in the main properties of the transparent electrically conductive layer – color and resistance. Before and after laser processing, the surface resistance of FTO glasses was 12.1±0.9 and 14.4±1.2 Ohm/sq., respectively. In addition, it was found that the processing of Ni(OH)2-polyvinyl alcohol films improved the adhesion of the latter to the surface of FTO glass. Based on the data obtained, a selective method was proposed for modifying thin colored films deposited on transparent conductive oxides (FTO, ITO, AZO) by visible laser radiation. This approach to changing the properties of films can be useful for areas related to the development of sensors, microelectronics, solar cells, small-sized current sources, electrodes with high efficiency, etc.
Laser Nanofabrication: Applications in Micro-Optics, Micro-Electronics, Micromachines, and Microfluidics

Chen, Qi-Dai,Xia, Hong,Yong-Lai Zhang,Sun, Hong-Bo

DOI: https://doi.org/10.1109/cleoe.2011.5943341

2011-01-01

Abstract:Femtosecond laser micronanofabrication has been considered as a promising approach for complicated device fabrication in versatile fields due to its intrinsic three-dimensional (3D) prototyping capability and reasonably high fabrication accuracy up to tens of nanometers. However, the unique features haven't been fully demonstrated yet so far. Our research in the passed several years has been focused in exploring applications of delicate technology in micro-optics, microelectronics, micromachines and microfluidics. Significant progress has been achieved. Successful examples include but not limited to aspheric microlens arrays with 100% filling ratio and numerical aperture as high as 0.5, nonplanar metal nanowiring technology, flexible circuits of graphene, remotely magnetically controllable micromachine, and microfilter and microturbines for microfluidic channels. Details on the fabrication and characterizations on these devices will be presented.
Laser Micronanostructuing For High-Performance Organic Optoelectronic Devices

Hong-Bo Sun

DOI: https://doi.org/10.1364/cleo_at.2014.atu2l.3

2014-01-01

Abstract:We report series of work on multi-beam interference ablation of organic materials, by which problems like extract efficiency and view angle in OLED were solved. The devices are promising for high-efficiency and long-life time display.We report series of work on multi-beam interference ablation of organic materials, by which problems like extract efficiency and view angle in OLED were solved. The devices are promising for high-efficiency and long-life time display.
New Organic thermally stable materials for optoelectronics devices - A linear spectroscopy study

O.S. Prelipceanu,M. Prelipceanu,O.G. Tudose,B. Grimm,S. Schrader

DOI: https://doi.org/10.48550/arXiv.0704.0572

2007-04-04

Abstract:Thermally stable polymers have attracted a lot of interest due to their potential use as the active component in electronic, optical and optoelectronic applications, such as light-emitting diodes, light emitting electrochemical cells, photodiodes, photovoltaic cells, field effect transistors, optocouplers and optically pumped lasers in solution and solid <a class="link-external link-http" href="http://state.We" rel="external noopener nofollow">this http URL</a> report results of investigations into the use of thermal treatment of poly(p-phenylene vinylene) (PPV) films grown on a variety of substrates (quartz and glass). Film thickness, morphology and structural properties were investigated by a range of techniques in particular: atomic force microscope - AFM, DEKTAK method, Ellipsometry and UV-VIS spectroscopy.

Other Condensed Matter,Materials Science
Electronic relaxation in PLD TiO 2 films processed with femtosecond UV-laser

L. Museur,A. Klini,L. Papoutsakis,A. Manousaki,A. Englezis,C. Colbeau-Justin,A. Kanaev

DOI: https://doi.org/10.1016/j.cplett.2024.141368

IF: 2.719

2024-05-28

Chemical Physics Letters

Abstract:Modifications of shallow electron trap states near conduction band was analyzed after surface structuring of TiO 2 thin films prepared via pulsed laser deposition method. Laser-induced periodic surface structures (LIPSS) were produced on the large-area films after irradiation with femtosecond KrF laser (λ = 248 nm). While spatial period of LIPSS Λ ≈ 190 ± 10 nm was not affected by laser fluence, coherence was increased with an increase of laser dose. Time-resolved microwave conductivity measurements accompanied by theoretical modelling revealed energetic positions of shallow electron trap states, connected to LIPSS. A possibility to alter the trap states energy via surface structuring of the material was shown.

chemistry, physical,physics, atomic, molecular & chemical

Laser Prepared Thin Films for Optoelectronic Applications

Amorphous thin films for mechanically flexible, multimaterial integrated photonics

Thin Films of Metal-Organic Framework Interfaces Obtained by Laser Evaporation

Laser Processing of Emerging Nanomaterials for Optoelectronics and Photocatalysis

Laser Technology for Perovskite: Fabrication and Applications (Adv. Mater. Technol. 10/2024)

Compressing High Energy Lasers through Optical Polymer Films

Photoablative Etching of Materials for Optoelectronic Integrated Devices

Coprocessed heterogeneous near-infrared lasers on thin-film lithium niobate

Methodology of selective metallic thin film ablation from susceptible polymer substrate using pulsed femtosecond laser

Micro-/Nano-Structures Fabricated by Laser Technologies for Optoelectronic Devices

Investigation of laser-induced changes in structural and optoelectrical properties of pulsed laser-deposited Diamond-Like Carbon layers

Biomolecular papain thin films growth by laser techniques

Laser Micro-Fabrication/Manipulation of Dielectric Materials

LIPSS on thin metallic films: New insights from multiplicity of laser-excited electromagnetic modes and efficiency of metal oxidation

Laser-assisted two dimensional material electronic and optoelectronic devices

Phenomenological studies of femtosecond laser ablation on optical thin films for integrated photonics

A study of the possibility of conducting selective laser processing of thin composite electrochromic Ni(OH)2-PVA films

Laser Nanofabrication: Applications in Micro-Optics, Micro-Electronics, Micromachines, and Microfluidics

Laser Micronanostructuing For High-Performance Organic Optoelectronic Devices

New Organic thermally stable materials for optoelectronics devices - A linear spectroscopy study

Electronic relaxation in PLD TiO 2 films processed with femtosecond UV-laser