Abstract:The strain rate and temperature effects on the hydrogen embrittlement behavior of Fe-20Mn-20Ni-20Cr-20Co and Fe-30Mn-10Cr-10Co (at %) high-entropy alloys were investigated. The Fe-20Mn-20Ni-20Cr-20Co high-entropy alloy exhibits a mechanically stable face-centered cubic (FCC) structure. The as-annealed microstructure of the Fe-30Mn-10Cr-10Co high-entropy alloy consists of a metastable FCC phase with a thermally induced hexagonal close-packed (HCP) martensite. After hydrogen precharging in a 100-MPa hydrogen gas atmosphere, tensile tests were carried out on the two high-entropy alloys. The hydrogen increased the yield strength of both alloys. With the increase in strain rate from 10 –4 to 10 –2 s –1 , the yield strength of the hydrogen-charged Fe-20Mn-20Ni-20Cr-20Co alloy markedly increased, which indicates activation of the strengthening mechanism related to the thermal activation of dislocation motion associated with hydrogen atoms. In contrast, the strain rate effect on the yield strength was insignificant in the Fe-30Mn-10Cr-10Co alloy, where the FCC–HCP martensitic transformation dominated the onset of plasticity. In terms of failure, the combined hydrogen effects that increased the flow stress and decreased the work-hardening rate in the late deformation stage accelerated the occurrence of specimen necking, particularly at a high strain rate, e.g. 10 –2 s –1 at 20°C. In addition, the elongation of the hydrogen-charged Fe-20Mn-20Ni-20Cr-20Co and Fe-30Mn-10Cr-10Co alloys increased with the strain rate, which indicates that the hydrogen transport by dislocation motion in late deformation stages assisted both modes of cracking (along grain boundaries and HCP martensite plates) in high-entropy alloys, which resulted in hydrogen-induced intergranular fracture and quasi-cleavage fracture, particularly at relatively low strain rates. Importance of the hydrogen transport by dislocation motion for brittle fracture at 20°C was supported by the test results at –100°C: brittle fracture occurred at higher stress and larger strain as compared to the cases at 20°C for both alloys.

Material performance of age-hardened beryllium–copper alloy, CDA-C17200, in a high-pressure, gaseous hydrogen environment

Effect of Hydrogen Charging on the Mechanical Properties of High-Strength Copper-Base Alloys, Austenitic Stainless Steel AISI 321, Inconel 625 and Ferritic Steel 1.4511

Crack Growth Analysis Of High-Pressure Equipment For Hydrogen Storage

Hydrogen storage alloys for high-pressure suprapure hydrogen compressor

Design Fatigue Life Evaluation of High-Pressure Hydrogen Storage Vessels Based on Fracture Mechanics

Overview of hydrogen-resistant alloys for high-pressure hydrogen environment: on the hydrogen energy structural materials

Hydrogen embrittlement behaviors during SSRT tests in gaseous hydrogen for cold-worked type 316 austenitic stainless steel and iron-based superalloy A286 used in hydrogen refueling station

Effects of High Pressure Hydrogen on Mechanical Properties of 6061 Aluminum Alloy

Study on Rare Earth Based Hydrogen Storage Alloy for High-pressure Metal Hydride Hydrogen Compressor

Determination of hydrogen compatibility for Cu-Al-Ni-Fe-Mn cast alloys prepared by varying Al and Ni contents

Metallic Material Evaluation of Liquid Hydrogen Storage Tank for Marine Application Using a Tensile Cryostat for 20 K and Electrochemical Cell

Hydrogen diffusivity, uptake and embrittlement of solution annealed and cold deformed austenitic stainless steel 1.4435 at hydrogen pressures up to 1000 bar and 200 °C

Hydrogen-assisted decohesion associated with nanosized grain boundary κ-carbides in a high-Mn lightweight steel

The influence of aging on microhardness and electrical conductivity of Cu–2 wt. % Be alloy

Strain Rate and Temperature Effects on Hydrogen Embrittlement of Stable and Metastable High-Entropy Alloys

Hydrogen-enhanced microbanding in an austenitic FeMnAlC low-density steel: Effect on hydrogen embrittlement resistance

Hydrogen Compression Materials with Output Hydrogen Pressure in a Wide Range of Pressures Using a Low-Potential Heat-Transfer Agent

Hydrogen embrittlement susceptibility of additively manufactured 316L stainless steel: influence of post-processing, printing direction, temperature and pre-straining

Temperature-Dependent Hydrogen Embrittlement of Austenitic Stainless Steel on Phase Transformation

Development of (Ti–Zr) 1.02 (Cr–Mn–Fe) 2 -Based Alloys toward Excellent Hydrogen Compression Performance in Water-Bath Environments

Optimization of AB2 type alloy composition with superior hydrogen storage properties for stationary applications