Abstract:Introduction. Multilayer high-temperature coatings obtained using plasma spraying, are studied. The combination of layers of different chemical and phase compositions made it possible to increase wear resistance by 1.5–2.0 times. The purpose of this work is to study the influence of the chemical composition of sprayed coatings on the phase composition, structure, micromechanical and tribological characteristics under conditions of dry sliding friction of surface layers. Materials and methods of research. Coatings A and B consist of sequentially sprayed layers. The first and second layers were sprayed in a reducing atmosphere: the first layer was a heat-resistant self-fluxing powder of two systems: 1 – Fe-Cr-Si-Mn-B-C for coating A and 2 – Fe-Ni-Si-Mn-B-C for coating B; the second layer was a mixture of self-fluxing powder with iron powder in a 1:1 ratio. The third layer was obtained by spraying iron powder in an oxidizing atmosphere to form a metal oxide coating. To create a layer of scale on the surface, coated specimens were subjected to high-temperature annealing at a temperature of 1,000 °C. The chemical composition and nature of the distribution of elements over the thickness of the coatings were determined by micro-X-ray spectral analysis using a TWSCAN scanning electron microscope with an Oxford energy-dispersive attachment. Microhardness and micromechanical properties were studied using an instrumental microhardness tester of the Fischerscope HM2000 XYm system at a load of 0.980 N. Determination of tribological properties was carried out on a laboratory installation using the “finger-disc” scheme at loads of 30, 75, 100 and 130 N. To measure roughness parameters and obtain 3-D profilometry of surfaces after testing, a non-contact profilometer-profiler Optical profiling system Veeco WYKO NT 1100 was used. Results and discussion. Metallographic studies have shown that the formed multilayer coatings consist of an internal metal layer and an external oxide layer with a total thickness of the entire coating up to 800–850 μm. It is established that the first sprayed layer has the highest level of microhardness, which is due to the high-volume fraction of the strengthening phases contained in it (~ 95 %). It is shown that the coating A has increased wear resistance, which is expressed by minimal weight loss (~ 1.5 times less than that of the coating of the coatimg B), the friction coefficient was f = 0.3 for coating A and f = 0.4 for coating B. The study of wear surfaces has shown that for all selected test loads under sliding friction conditions, the coating of both compositions was preserved, even at a maximum load of 130 N.

Effect of the Structure of TiB2–(Fe–Mo) Plasma Coatings on Mechanical and Tribotechnical Properties

Structural features and tribological properties of multilayer high-temperature plasma coatings

Microstructure and Properties of Al2O3-13wt.%TiO2-Reinforced CoCrFeMnNi High-Entropy Alloy Composite Coatings Prepared by Plasma Spraying

Microstructure and Tribological Property of TiC-Mo Composite Coating Prepared by Vacuum Plasma Spraying

INFLUENCE OF THE STRUCTURE OF IRON-TITANIUM THERMAL SPRAYED COATINGS ON THEIR WEAR RESISTANCE

Influence of graphite additive on microstructure and mechanical characteristics of plasma sprayed TiB2–TiC composite coating

The Influence of Distance Pulsed Plasma Treatment on the Structure and Properties of Detonation Coatings from Eutectic Alloy Fe-TiB2-CrB2

Microstructure and properties of Al2O3–ZrO2–TiO2 composite coatings prepared by plasma spraying

Deposition and properties of plasma sprayed NiCrCoMo–TiC composite coatings

Microstructure and tribological properties of atmospheric plasma-sprayed TiO2 coatings reinforced by boron nitride nanosheets

Laser Cladding of a Ti–Zr–Mo–Ta–Nb–B Composite Coating on Ti60 Alloy to Improve Wear Resistance

Tribo-Mechanical Properties of HVOF Deposited Fe₃Al Coatings Reinforced with TiB₂ Particles for Wear-Resistant Applications

Wear Properties of Plasma Transferred Arc Fe-based Coatings Reinforced by Spherical WC Particles

Effect of MoS2 Content on Microstructure and Properties of Supersonic Plasma Sprayed Fe-based Composite Coatings

Effect of the Adhesive Properties of Vacuum Ion-Plasma TiAlN Coatings on Wear Resistance in Friction

Fe-based amorphous/nanocrystalline composite coating by plasma spraying: Effect of heat input on morphology, phase evolution and mechanical properties

Effect of Chromium Carbide Addition on the Microstructures and Properties in Dual Carbide Phases Reinforced Ni-Based Composite Coatings by Plasma Cladding

Study on Plasma Sprayed 40%Zro_2-Al_2o_3-13%tio_2 Ceramic Coatings and Tribological Properties

Microstructure evolution and mechanical properties of reactive plasma sprayed Ti3SiC2–Ti5Si3–TiC composite coatings

Microstructure and tribological properties of ZrB 2 -enhanced NiCrBSi coatings prepared by high-velocity oxy-fuel spraying

Microstructure and properties of CrB2-Cr3C2 composite coatings prepared by plasma spraying