Abstract:Recovering ethane from natural gas involves significant energy consumption. Globally, the recycle split vapor process (RSV) is widely adopted as an efficient method for ethane recovery. Nonetheless, one major challenge faced by the RSV process is the lack of adequate heat integration, despite its overall effectiveness. In this article, we investigate the heat integration of the RSV process and propose two novel ethane recovery processes: the recycle split vapor process with direct heat integration of the feed gas (RSV‐DTI) and the recycle split vapor process with split heat integration of the feed gas (RSV‐SHI). A comparative analysis is conducted among these three processes, focusing on integrated energy consumption, exergy efficiency, and economic investment. The study's findings reveal the following: (1) The RSV‐DTI process distinguishes itself with its reduced energy consumption, enhanced stability, and minimized refrigerant usage. In comparison to the RSV process, the RSV‐DTI process achieves a reduction of over 15% in total compression duty and a remarkable decrease of 68% in propane usage. (2) Electricity emerges as the predominant energy consumed in the ethane recovery process, and the RSV‐DTI process significantly improves upon this aspect. Notably, the RSV‐DTI process incurs the lowest investment cost, yielding a swift payback period of approximately 1 year for the plant. The characteristics of the RSV‐DTI process are investigated, and the effect of changes in feed gas conditions on the heat integration of the RSV‐DTI process is analyzed. The characteristics of the RSV‐DTI process show the following: (1) Different pressures of feed gas existing in the main cold box have different minimum heat integration temperatures (MHIT). When the feed gas temperature is lower than the MHIT, heat integration becomes difficult, and the heat energy can be supplied by hot liquid propane at 48°C. When the feed gas temperature is higher than the MHIT, changes in feed gas temperature have little effect on the process, only affecting the external gas temperature. (2) The heat transfer duty of the demethanizer sideline outlet stream is affected by the feed gas pressure. To enhance heat integration, it is recommended to set the heat transfer duty of the low‐temperature sideline outlet stream (DLTSS) between 40% and 90% of the reboiler duty and the heat transfer duty of the high‐temperature sideline outlet stream (DHTSS) between 40% and 75% of the reboiler duty.

Study on Dynamic Heat Extraction Characteristics of Heat Exchanger Tube Embedded in Thermal Flow Reverse Reactor for Heat Recovery

Investigations on the mitigation of ventilation air methane and energy recovery in site trial thermal flow-reversal reactor

Strategies for heat recovery in a reverse flow reactor designed to lessen coal mine methane emissions test

A control strategy of flow reversal with hot gas withdrawal for heat recovery and its application in mitigation and utilization of ventilation air methane in a reverse flow reactor

Thermo-hydraulic Characteristics of Offset Strip Fin Heat Exchanger with Vortex Generators

Experimental Research on the Thermal Oxidation of Ventilation Air Methane in a Thermal Reverse Flow Reactor

Numerical Evaluation of Heat Transfer and Conversion Efficiency by Tube Design and Flow Configuration for a Compact Steam-Methane Reformer

Design and Performance Investigation of a Compact Catalytic Reactor Integrated with Heat Recuperator

Catalytic or thermal reversed flow combustion of coal mine ventilation air methane: What is better choice and when?

Analysis of the Effects of Structural Parameters on the Thermal Performance and System Stability of Ventilation Air Methane-Fueled Reverse-Flow Oxidation Reactors

Stainless steel finned tube heat exchanger design for waste heat recovery

Demonstration of mitigation and utilization of ventilation air methane in a pilot scale catalytic reverse flow reactor

Experimental and numerical investigation of turbulent heat transfer enhancement of an intermediate heat exchanger using corrugated tubes

Numerical simulation of heat transfer performance of different heat exchange tubes in heat recovery steam generator

Numerical investigation of extracted position characteristics in porous media with lean methane and air premixtures combustion

Innovative Fixed-Bed Reactor Integrated with Heat Transfer System for Lean Methane Mixture Removal

Combustion Characteristics of Ventilation Air Methane Blending with Dimethyl Ether in a Thermal Reverse Flow Reactor

Demonstration and its validation for ventilation air methane (VAM) thermal oxidation and energy recovery project

Heat integration analysis based on recycle split vapor ethane recovery process

Dynamic simulation of a gas turbine for heat recovery at varying load and environment conditions

Methods for improving heat exchanger area distribution and storage temperature selection in heat recovery loops