Abstract:The affiliations of the authors in the original version of this article were unfortunately incorrect on the first page and the first page of the ESM.Instead ofYan Zhang1,2, Jiaheng Nie1, and Lijie Li3 (✉)1 School of Physical Electronics, University of Electronic Science and Technology of China, Chengdu 610054, China2 Beijing Institute of Nanoenergy and Nanosystems, Chinese Academy of Sciences, National Center for Nanoscience and Technology (NCNST), Beijing 100083, China3 Multidisciplinary Nanotechnology Centre, College of Engineering, Swansea University, Swansea SA1 8EN, UKIt should readYan Zhang1,2,3, Jiaheng Nie1, and Lijie Li4 (✉)1 School of Physics, School of Physical Electronics, University of Electronic Science and Technology of China, Chengdu 610054, China2 Beijing Institute of Nanoenergy and Nanosystems, Chinese Academy of Sciences, Beijing 100083, China3 College of Nanoscience and Technology, University of Chinese Academy of Sciences, Beijing 100049, China4 Multidisciplinary Nanotechnology Centre, College of Engineering, Swansea University, Swansea SA1 8EN, UK

Erratum to: Generation of graphene-based aerogel microspheres for broadband and tunable high-performance microwave absorption by electrospinning-freeze drying process

Publisher Correction: Chalcogenide Glass-on-graphene Photonics

Erratum To: N-doped Graphene Quantum Dots-Functionalized Titanium Dioxide Nanofibers and Their Highly Efficient Photocurrent Response

Erratum: Corrigendum: Printing, folding and assembly methods for forming 3D mesostructures in advanced materials

Erratum to: Highly active zigzag-like Pt-Zn alloy nanowires with high-index facets for alcohol electrooxidation

Corrections to “zinc Oxide Nanostructures and High Electron Mobility Nanocomposite Thin Film Transistors” [nov 08 3001-3011

Erratum To: Facile Fabrication of Biomimetic Water Pinning Microstructures on Polyethylene Surfaces with Robust Superhydrophobic Wetting State

Erratum: 3D Printing Fiber Electrodes for an All-Fiber Integrated Electronic Device Via Hybridization of an Asymmetric Supercapacitor and a Temperature Sensor.

Correction to “broadband Light Amplitude Tuning Characteristics of SnSe2 Coated Microfiber” [nov 20 6089-6096]

Erratum: Substrate-induced Bandgap Opening in Epitaxial Graphene.

Erratum: Zhang, C. et al., The Effect of Substrate Biasing during DC Magnetron Sputtering on the Quality of VO2 Thin Films and Their Insulator–Metal Transition Behavior. Materials 2019, 12, 2160

Erratum: Corrigendum: Magnetization Reversal by Out-of-plane Voltage in BiFeO3-based Multiferroic Heterostructures

Erratum to “The Possibility of Changing the Wettability of Material Surface by Adjusting Gravity”

Correction To: Fabrication of High-Strength Polyoxymethylene Fibers by Gel Spinning

Erratum to: Piezotronic effect on the luminescence of quantum dots for micro/nano-newton force measurement

Corrigendum to “In situ synthesis of MgAlB4 whiskers as a promising reinforcement for aluminum matrix composites”[Mater. Sci. Eng. A 764 (2019) 138229]

Correction: Corrigendum: Optoelectronic Crystal of Artificial Atoms in Strain-Textured Molybdenum Disulphide

Corrigendum: Dispersing Carbon Nanotubes with Graphene Oxide in Water and Synergistic Effects Between Graphene Derivatives

Erratum: Wang, D., Et Al. Self-Assembly Synthesis of the MoS2/PtCo Alloy Counter Electrodes for High-Efficiency and Stable Low-Cost Dye-Sensitized Solar Cells. Nanomaterials 2020, 10, 1725.

Correction to: New surface microstructure of mono-si wafer textured using wet chemical solutions for solar cell

Correction: Fabrication of free-standing membranes with tunable pore structures based on the combination of electrospinning and self-assembly of block copolymers