Abstract:This article introduces an innovative approach to the investigation of the conductive-radiative heat transfer mechanism in expanded polystyrene (EPS) thermal insulation at negligible convection. Closed-cell EPS foam (bulk density 14-17 kg·m-3) in the form of panels (of thickness 0.02-0.18 m) was tested with 1-15 µm graphite microparticles (GMP) at two different industrial concentrations (up to 4.3% of the EPS mass). A heat flow meter (HFM) was found to be precise enough to observe all thermal effects under study: the dependence of the total thermal conductivity on thickness, density, and GMP content, as well as the thermal resistance relative gain. An alternative explanation of the total thermal conductivity "thickness effect" is proposed. The conductive-radiative components of the total thermal conductivity were separated, by comparing measured (with and without Al-foil) and simulated (i.e., calculated based on data reported in the literature) results. This helps to elucidate why a small addition of GMP (below 4.3%) forces such an evident drop in total thermal conductivity, down to 0.03 W·m-1·K-1. As proposed, a physical cause is related to the change in mechanism of the heat transfer by conduction and radiation. The main accomplishment is discovering that the change forced by GMP in the polymer matrix thermal conduction may dominate the radiation change. Hence, the matrix conduction component change is considered to be the major cause of the observed drop in total thermal conductivity of EPS insulation. At the microscopic level of the molecules or chains (e.g., in polymers), significant differences observed in the intensity of Raman spectra and in the glass transition temperature increase on differential scanning calorimetry(DSC) thermograms, when comparing EPS foam with and without GMP, complementarily support the above statement. An additional practical achievement is finding the maximum thickness at which one may reduce the "grey" EPS insulating layer, with respect to "dotted" EPS at a required level of thermal resistance. In the case of the thickest (0.30 m) panels for a passive building, above 18% of thickness reduction is found to be possible.

Density profiles of novel kraft pulp and TMP based foam formed thermal insulation materials observed by X-ray tomography and densitometry

Renewable Insulation Panels Made with Cynodon Dactylon Grass for Building Applications: Physical, Mechanical, Acoustic, and Thermal Properties

Analyzing wood bark insulation board structure using X-ray computed tomography and modeling its thermal conductivity by means of finite difference method

The research for new material and new technology of exterior walls thermal insulation

Preparation and Properties of Expanded Vermiculite/Gypsum Thermal Insulation Boards

Investigation of various hardwood and softwood fibres for the usage in wood-fibre insulation panels

Pore structure characterization and effective thermal conductivity modeling of fibrous building thermal insulation materials based on X-ray tomography

Intra-Ring Wood Density and Dynamic Modulus of Elasticity Profiles for Black Spruce and Jack Pine from X-ray Densitometry and Ultrasonic Wave Velocity Measurement

Investigation of both thermal parameters and applications of closed-cell plastic thermal insulation foams with building energetic aspects

Change in Conductive-Radiative Heat Transfer Mechanism Forced by Graphite Microfiller in Expanded Polystyrene Thermal Insulation-Experimental and Simulated Investigations

Development of Plant Fibre Foam and Study of Its Thermal Insulation Properties

Practical Use of Materials of Natural Origin as Loose-Fill Insulations in Open-Diffusion Constructions—Observation and Numerical Simulation

Biomass-derived wood foam: a solution for efficient thermal insulation in construction

Direct Observation and Measurement of Fiber Architecture in Short Fiber-Polymer Composite Foam Through Micro-Ct Imaging

Three-dimensional geometry, pore parameter, and fractal characteristic analyses of medium-density fiberboard by X-ray tomography, coupling with scanning electron microscopy and mercury intrusion porosimetry

An experimental toolbox for the physical characterization of thermal insulating polymeric foams

An Investigation into the Relationship between Density and Pulverization Ratio for Tannin-Furanic Foam

Thermal Performance of Lignocellulose's By-Product Wallboards with Bio-Based Microencapsulated Phase Change Materials

Thermal Insulation Panels with Bio-Based Adhesives

Sound absorption properties of wood-based pulp fibre foams

Eco-foaming Lignin for Innovative Rigid Foams