Abstract:Numerical simulation of inertial confinement fusion (ICF) capsule implosion experiments requires many plasma parameters corresponding to different materials and their mixtures for a wide range of densities and temperatures. Thermal conduction plays a crucial role in coupling energy to the capsule, is one of the primary mechanisms of energy loss during implosion, has a significant effect on hot-spot formation, and impacts the growth of hydrodynamic instabilities. The determination of accurate thermal conductivity of ICF relevant materials is thus important for understanding capsule performance. Analytic models such as Spitzer or Lee-More models have been extensively used in simulations due to the limited availability of experimental data. First principles calculations have shown that these analytic models tend to underestimate electron thermal conductivity in the warm dense plasma regime for ICF related materials. In this paper, we numerically investigate the effects of different models for the electron heat conductivity coefficients, including both analytic and Quantum Molecular Dynamics (QMD)-based models, for mixed materials in ICF. We also investigate the impact of how conductivities are calculated in mixed cells from constituent material conductivities. We apply this to the modeling of recent wetted foam capsule implosions on the National Ignition Facility, in which a foam layer on the inside of the capsule is wetted with deuterium-tritium (DT) liquid. We have found that electron heat conductivity affects the initial hot-spot formation and its evolution. Strikingly, we observe that capsule performance is more sensitive to the method used to mix material conductivities in mixed cells than how individual material conductivity coefficients are calculated. We have also found that using the first principles QMD-based conductivity model along with an appropriate model for mixed-cell conductivities yields better agreement with experimental results compared to the established modeling strategies. We also investigate the impact of mixed material conductivity modeling on the process of ablator material mixing with DT ice in a plastic ice-layer capsule. In our simulations, the heat conductivity model affects the calculated mix widths at the fuel-ablator interface, particularly near the tent scar. Additional mixing between the DT fuel and the ablator in turn increases the implosion adiabat, which results in a lower hot-spot pressure.

Capsule physics comparison of National Ignition Facility implosion designs using plastic, high density carbon, and beryllium ablators

Beryllium capsule implosions at a case-to-capsule ratio of 3.7 on the National Ignition Facility

Carbon Ablator Areal Density at Fusion Burn: Observations and Trends at the National Ignition Facility

Comparison of ablators for the polar direct drive exploding pusher platform

Thin Shell, High Velocity Inertial Confinement Fusion Implosions on the National Ignition Facility

Transition in ICF Capsule Implosions

Effects of thermal conductivity of liquid layer in NIF wetted foam experiments

A “polar contact” tent for reduced perturbation and improved performance of NIF ignition capsules

Understanding asymmetries using integrated simulations of capsule implosions in low gas-fill hohlraums at the National Ignition Facility

Simulated impact of fill tube geometry on recent high-yield implosions at the National Ignition Facility

Simulated signatures of ignition

Measurement of mix at the fuel–ablator interface in indirectly driven capsule implosions on the National Ignition Facility

Capsule implosions for continuum x-ray backlighting of opacity samples at the National Ignition Facility

First High-Convergence Cryogenic Implosion in A Near-Vacuum Hohlraum

Toward a burning plasma state using diamond ablator inertially confined fusion (ICF) implosions on the National Ignition Facility (NIF)

Infuence of mass ablation on ignition and burn propagation in layered fusion capsules

A Near One-Dimensional Indirectly Driven Implosion at Convergence Ratio 30

Demonstration of High Performance in Layered Deuterium-Tritium Capsule Implosions in Uranium Hohlraums at the National Ignition Facility.

Progress Towards Ignition on the National Ignition Facility

Investigation of Ion Kinetic Effects in Direct-Drive Exploding-Pusher Implosions at the NIF

Design and Modeling of Indirectly-Driven Magnetized Implosions on the NIF