Abstract:Different stages of preparation, evaluation and presentation of energy absorption applications for 3D printed LDPE‐POE blends. Polyolefins and polyolefin elastomers (POEs) are widely used in various applications due to their unique properties. However, their use in 3D printing has been limited due to challenges such as excessive softness, shrinkage, warpage, and poor mechanical properties. In this study, two strategies were employed to enhance the performance of POEs in 3D printing. First, POE was blended with 10%, 30%, and 50% percentages of linear low‐density polyethylene (LLDPE) to improve the material's mechanical properties and printability. Second, a specialized printer called a pneumatic feeding fused granule fabrication (FGF) printer was used. This printer allows for the direct printing of material granules, eliminating the need for filaments and resolving filament‐related problems. To evaluate the quality of the printed parts, tensile tests, dynamic mechanical thermal analysis (DMTA), and scanning electron microscopy (SEM) imaging were conducted. The printed parts showed desirable tensile properties (with approximately 3000% elongation at break and approximately 12 MPa tensile strength). Compression tests were also conducted on cubic structures with varied composition ratios and printing patterns such as grid, triangle, and honeycomb. The main purpose of this research was to explore the energy absorption capabilities of the printed blends. The results of our study showed that blending POE with LLDPE improved printability, tensile strength, energy absorption, and compressive properties. The blend with 50% LLDPE and honeycomb structure exhibited the best compressive and energy absorption properties. Highlights Blending of POE and LLDPE using melt mixing with three different blending ratios. Successful 3D printing with the fused granule fabrication technique. Investigating mechanical properties, microstructure, and thermal analysis. 125% increase in ultimate tensile strength by increasing LLDPE. Achieving the highest energy absorption for the 3D printed honeycomb structure.

Effects of POE-g-MAH on properties of PP-based binder in metal injection molding

Research on Toughening Modification of Copolymerized Polypropylene Using Polyolefin Elastomers

Preparation of high melt strength polypropylene by the reactive extrusion process and its foaming application

Preparation of PBT/POE‐g‐GMA/PP Ternary Blends with Good Rigidity–toughness Balance by Core–shell Particles

Morphology, rheology, and mechanical properties of polylactide/ poly(ethylene-co-octene) blends

Effects of PVP Incorporation on the Properties of Injection-Molded High-Performance Ceramics with PEG-based Binders

Fracture behavior and deformation mechanism of polypropylene/ethylene-octene copolymer/magnesium hydroxide ternary phase composites

Effect of Increased Powder-Binder Adhesion by Backbone Grafting on the Properties of Feedstocks for Ceramic Injection Molding

Effect of glycidyl methacrylate-grafted poly(ethylene octene) on the compatibility in PLA/PBAT blends and films

The effect of Polyolefin elastomer on the 3D printing properties of Acrylonitrile butadiene styrene, Polyethylene, and Polypropylene

Preparation and performance study of POE-g-MAH/GMA toughened bio-based PA56 alloys

Enhancing Mechanical Performance of High-Lignin-Filled Polypropylene via Reactive Extrusion

Synergy of low-and high-density polyethylene in a binder system for powder injection molding of SiC ceramics

Enhanced compatibility of PA6/POE blends by POE-g-MAH prepared through ultrasound-assisted extrusion

Effects of Calcium Carbonate and Compounding Sequence on the Phase Morphology and Properties of Maleic Anhydride-Grafted Polypropylene Compatibilized Polyamide 6/polypropylene Blend

Effect of Morphology Development on the Low‐temperature Tensile Properties of PP / POE Blends

A novel PEG/PMMA based binder composition for void-free metal injection moulding of Ti components

Structure and Properties of Polyoxymethylene/Silver/Maleic Anhydride-Grafted Polyolefin Elastomer Ternary Nanocomposites

Thermal, mechanical and morphological properties of plasticized polyurethane binders based on PEG and HTPB blends

Effects of the Binder Compositions on the Homogeneity of Ceramic Injection Molded Compacts

Influence of LLDPE on the mechanical properties improvement of 3D printed POE/LLDPE blends