Abstract:Abstract Laboratory experiment and thermodynamic calculation for the Ti-containing 24 mass pct Cr ferritic stainless steel with a CaO-SiO 2 -Al 2 O 3 -MgO system slag were performed to investigate the effect of slag addition on the inclusion characteristics in molten steel. The morphology, composition, and size evolution of inclusions in steel samples were analyzed in three-dimensional by the electrolytic extraction method and in two-dimensional by the automatic analysis method. The results showed that the Ti content significantly decreased after the slag addition. However, the change of the Si content showed an opposite tendency. The decrease of the Ti content in steel was due to the reduction of SiO 2 and Al 2 O 3 in the slag by dissolved Ti in steel. An increase of the TiO 2 content in the slag can decrease the Ti loss in steel based on the slag-steel kinetic analysis. The total O content in the steel melt decreased from 62 to 26 ppm, and the steel cleanliness was improved, since the number density of inclusions decreased after the slag refining. The results of a kinetic analysis showed that the rate-determining step of the oxidation of Ti in the steel and the reduction of SiO 2 in the slag were the mass transfer on the slag side. In addition, high Ti 2 O 3 -containing inclusions were found to be transformed to Cr 2 O 3 -Ti 2 O 3 -Al 2 O 3 and Cr 2 O 3 -Ti 2 O 3 -SiO 2 system inclusions after the slag addition. The Al 2 O 3 contents in inclusions increased while the Ti 2 O 3 contents decreased with time. However, there were some amount of high melting point inclusions with high Al 2 O 3 content, which were not what we expected. When plotted on logarcxithmic scales, the mole ratio $$X_{{{\text{Al}}_{2} {\text{O}}_{3} }} /(X_{{{\text{Ti}}_2 {\text{O}}_{3} }} \cdot X_{{{\text{Cr}}_{2} {\text{O}}_{3} }} )$$ X Al 2 O 3 / ( X Ti 2 O 3 · X Cr 2 O 3 ) values of the inclusions were expressed as a linear function of the $$a_{\text{Al}}^{2} /(a_{Ti}^{2} \cdot a_{\text{Cr}}^{2} \cdot a_{\text{O}}^{3} )$$ a Al 2 / ( a Ti 2 · a Cr 2 · a O 3 ) values of the steel melts with a slope of unity, which was theoretically expected.

Evolution Mechanism of Oxide Inclusions in Titanium-Stabilized AISI 443 Stainless Steel

Evolution behaviour of nonmetallic inclusions in Ti-bearing 11Cr stainless steel with calcium treatment

Evolution of the Non-metallic Inclusions Influenced by Slag-Metal Reactions in Ti-Containing Ferritic Stainless Steel

Study on the thermodynamic stability and evolution of inclusions in Al–Ti deoxidized steel

Transient Behavior and Thermodynamics of Inclusions in Al-Ti-Deoxidized and Ca-Treated Steel

Effect of calcium content on inclusions during the ladle furnace refining process of AISI 321 stainless steel

Evolution mechanism of inclusions during refining and continuous casting process of 321H stainless steel

Characteristics and Modification of Non-metallic Inclusions in Titanium-Stabilized AISI 409 Ferritic Stainless Steel

Evolution of oxide and nitride inclusions during processing of stainless steel

Evolution of Inclusions and Associated Microstructure in Ti–Mg Oxide Metallurgy Steel

Evolution Pathway of Competitive Precipitation of Inclusions in Al–Ti‐Deoxidized Steel

Addition of Titanium Oxide Inclusions into Liquid Steel to Control Nonmetallic Inclusions

Inclusions and Microstructure of Steel Weld Deposits with Nanosize Titanium Oxide Addition

Characteristics and Formation Mechanism of Inclusions in 304L Stainless Steel during the VOD Refining Process

Thermodynamics of the Formation of Non-Metallic Inclusions during the Deoxidation of GCr15 Bearing Steel

Effects of Calcium Addition on Nonmetallic Inclusions in High‐Al Steel

Influence of refining process and utilization of different slags on inclusions, titanium yield and total oxygen content of Ti-stabilized 321 stainless steel

Evolution behaviour of inclusions via oxide metallurgy of NM450 ultrahigh-strength steel

Atomistic Nucleation Mechanism of Titanium Oxides in Steel Based on Homogeneous and Heterogeneous Modes

Characteristics and Transformation Mechanism of Nonmetallic Inclusions in 304 Stainless Steel during Heat Treatment at 1250 °C

Effect of Calcium Addition on Oxide and Sulfide Inclusions in Heavy Steel Ingot Simulated by Lab Experiments