Abstract:This study explores an efficient and feasible method for production of non-commercial Co-Cr-Mo powder feedstock for Laser Powder Bed Fusion (LPBF), employing mechanical alloying (MA) with following thermal treatment. Elemental Co, Cr, and Mo powders were subjected to MA to create a powder nanostructured composite. Initially, the mechanically alloyed powder had a mixed-phase state, with ε-phase as the main one (about 95 wt%) and impurities of Cr 2 O 3 . However, an additional 1.5-hour of isothermal annealing at 400 °C successfully reduced the Cr 2 O 3 impurities and caused oxygen content to decrease, indicating a reduction in residual oxygen in the powder. This annealing process activated diffusion and induced relaxation of residual stresses, evidenced by decreased lattice microstrains: 0.8% for the Co-phase, 0.2% for both the Cr-phase and Mo-phase. Powder subjected to the thermal treatment was then utilized in LPBF to create bulk Co-Cr-Mo samples. The formed samples showed a typical LPBF microstructure represented by uniaxial cells and dendrites, with the distance between these structures not exceeding 3 μm. The samples showed homogenous elemental distribution, mixed-phase composition, and oxygen concentration not exceeding 5 wt%. In terms of mechanical properties , the LPBF samples exhibited a microhardness value of 4300 ± 200 MPa, ductility of 0.85, and yield strength of 1.4·10 3 MPa. Our method yields results comparable to those obtained from commercially spherical powder, indicating that our cost-effective approach does not sacrifice product quality. It represents a substantial cost reduction, approximately 4.5 times lower than that of commercial spherical powder, thereby highlighting the economic efficiency of our powder feedstock preparation for LPBF. Our findings underscore the potential of mechanically alloyed and thermally treated powder in LPBF. This worthwhile and efficient method of preparation powder feedstock breaks ground for more comprehensive facilities in 3D printing, cut down on cost of production with maintaining the high-quality output.

Comparison the Preparation Methods of Powder Feedstock for Laser Powder Bed Fusion

Comparative Study of Microstructure and Phase Composition of Amorphous-Nanocrystalline Fe-Based Composite Material Produced by Laser Powder Bed Fusion in Argon and Helium Atmosphere

Processing-microstructure relationships in ferrous alloys via mixed powder laser powder bed fusion

From Raw Elements to 3D Samples: An Economical Route for Co-Cr-Mo Alloy Fabrication

Effect of Powder Variability on Laser Powder Bed Fusion Processing and Properties of 316L

Laser Powder Bed Fusion of Powder Material: A Review

Progress in metallic powders for laser powder bed fusion

Comparison of characteristics of VZHL718 alloy metal powder compositions produced by prep and viga methods after selective laser melting

Role of powder particle size on laser powder bed fusion processability of AlSi10mg alloy

Effect of particle size distribution on the structure and mechanical properties in the process of laser powder bed fusion

Laser powder bed fusion recoater selection guide—Comparison of resulting powder bed properties and part quality

Powder Fabrication and Laser Powder Bed Fusion of a MoSiBTiC-La2O3 Alloy

Metal powder as feedstock for laser-based additive manufacturing: From production to powder modification

Influences of Powder Packing Density in Laser Powder Bed Fusion Metal Additive Manufacturing

Laser Powder Bed Fusion of Sm-Fe-N Bonded Magnets Employing Flake Powders.

Coated Metal Powders for Laser Powder Bed Fusion (L-PBF) Processing: A Review

Approach to Estimate the Phase Formation and the Mechanical Properties of Alloys Processed by Laser Powder Bed Fusion via Casting

Laser powder bed fusion of compositionally graded CoCrMo-Inconel 718

Characterization, preparation, and reuse of metallic powders for laser powder bed fusion: A review

Non-equilibrium solidification behavior associated with powder characteristics during electron beam additive manufacturing