Abstract:The material most commonly used to filter and clean the intake air of vehicle internal combustion engines is pleated filter paper, which in most cases is shaped in the form of a cylinder or panel. The production technology has a low cost and is not complicated. In addition to high separation efficiency and filtration performance, pleated filter media are required to have low initial pressure drop, which depends on the geometry of the bed. Much research has been conducted in this area. Dust accumulated in the filter bed causes an increase in pressure drop, which is the cause of deformation and sticking of pleats. The lack of stability of the pleats, the need to strengthen them, and the need to obtain small sizes while achieving high efficiency and accuracy of filtration of engine intake air was the reason for the development of a different design and a new technology for making filter cartridges called PowerCore. The distinctive feature of these filters is axial flow in one direction of the air stream, which avoids turbulence and thus minimizes pressure drop. This paper presents a comparative analysis of a standard PowerCore and PowerCore G2 filter bed and two cylindrical filters with a pleated filter bed made of cellulose and polyester. The conditions and methodology of experimental testing of filters with test dust are presented. During the tests, the characteristics of separation efficiency and filtration performance, as well as pressure drop as a function of the mass of dust retained on the filter of two PowerCore filters and two cylindrical filters were performed. Three specimens of test filters with the same filtration area were made from each sample of filter bed. The results showed that in each test of the filter bed, there is an initial filtration period characterized by low (96–98%) initial separation efficiency and the presence of large (dpmax) dust grains. As the dust loading of the bed increases, the separation efficiency and filtration performance obtain higher and higher values. The initial period of filtration ends when the conventional value (99.9%) of separation efficiency is reached. The duration of this period depends on the type of filter bed and for the PowerCore G2 filter ends for a dust loading of km = 33.1 g/m2, and for the cellulose filter for km = 117.3 g/m2. During the initial period, the air behind the PowerCore G2 filter contains grains with sizes in the range of dpmax = 9–16 μm. Behind the cellulose filter, dust grains are much larger, dpmax = 17–35 μm. The total operating time of the PowerCore G2 filter, limited by the achievement of the permittivity resistance Δpwdop = 3 kPa, is twice that of the other filter compositions tested.

Performance characteristics of air intake pleated panel filters for internal combustion engines in a two-stage configuration

Performance characteristics of air intake pleated panel filters for internal combustion engines in a two-stage configuration

Experimental Testing of Filter Materials for Two-Stage Inlet Air Systems of Internal Combustion Engines

Experimental Research of Fibrous Materials for Two-Stage Filtration of the Intake Air of Internal Combustion Engines

Experimental study of materials for the filtration of the intake air of the internal combustion engine of a motor vehicle

Experimental Study of Filtration Materials Used in the Car Air Intake

Experimental Studies of Dust Suction Irregularity from Multi-Cyclone Dust Collector of Two-Stage Air Filter

Experimental Studies of PowerCore Filters and Pleated Filter Baffles

Experimental Dust Absorption Study in Automotive Engine Inlet Air Filter Materials

Performance optimization of airliner cabin air filters

Experimental Study of the Effect of Air Filter Pressure Drop on Internal Combustion Engine Performance

Properties of material with nanofiber layer used for filtering the inlet air of internal combustion engines

Numerical investigation of pressure and flow characteristics of pleated air filter system for automotive engine intake application

Experimental Investigation of Possibilities to Improve Filtration Efficiency of Tangential Inlet Return Cyclones by Modification of Their Design

Filter Pleating Design for Cabin Air Filtration

A simple semi-numerical model for designing pleated air filters under dust loading

Filter Quality of Pleated Filter Cartridges

Empirical study of the effect of the air filter on the performance and exhaust emissions of a diesel engine

Numerical study of pleated fabric cartridges during pulse-jet cleaning

A numerical simulation method for pressure drop and normal air velocity of pleated filters during dust loading

Performance characterization of a novel compact dust collector with pleated filter cartridges