Abstract:Power plants are a major source of CO2 emissions in the environment, which cause global warming; due to this issue, CO2 capture from hydrocarbon fuels is one of the key technology options to reduce greenhouse gases. Pre-combustion capture of CO2 in the combined gas and steam turbine cycle has been investigated in this paper. The first step in the pre-combustion method is to react the fuel with oxygen, which comes from the air separation unit and produces a mixture of hydrogen and carbon monoxide. The CO is converted to CO2 in a water-shift reactor, and a physical absorbent removes the CO2; a hydrogen-rich fuel is produced, which can be burnt in a gas turbine with minimal CO2 emissions. This paper presents a thermodynamic cycle analysis, where pre-combustion CO2 capture is applied in a combined cycle where the main goal is to reduce the CO2 emission into the atmosphere. The main parameters are varied to examine the influence on cycle performance. The cycle performance results for the combined cycle with CH4 as fuel are presented and compared to the combined cycle with precombustion CO2 capture, both with and without Nitrogen injection into the compressor. An exergy analysis is carried out to determine which case has more exergy destruction. The results indicate that at 45 oC the combined cycle efficiency is raised by around 3 % when the pre-combustion CO2 capture without Nitrogen injection into the compressor is used, and the power output has been increased by 29 %. The performance of combined cycle with CO2 capture can be further enhanced by the N2 acquired from the air separation process and injected into the compressor’s middle stage. The results demonstrate a good improvement in the performance; the power output increases by 48 % and efficiency by 4.2 %. However, exergy destruction is increased when the CO2 capture, both with and without N2 injection into the compressor is used. Nevertheless, pre-combustion capture requires large monetary investment for a new-build plant where also the CO2 emission is reduced by 100 %.

Modeling, Performance Enhancement and the Nox Emissions Reduction of the Triple-Pressure Reheat Water-Recuperated Air-Cooled Gas Turbine Combined Cycle Power Plant Using Interstage Compressor Water Injection and Optimization

Techno-economic optimization and Nox emission reduction through steam injection in gas turbine combustion chamber for waste heat recovery and water production

Aerodynamic limits air injection for heavy-duty gas turbine: Compressor aerodynamic limits for power augmentation and ramp-up capabilities

Simulation and Optimization of Ion Transfer Membrane Air Separation Unit in an IGCC Power Plant

Integration Optimisation of Elevated Pressure Air Separation Unit with Gas Turbine in an Igcc Power Plant

Power augmentation and Ramp-Up rate improvement through compressed air Injection: A dry low NOx combustor CFD analysis

Thermal Energy Recovery from a Brayton Cycle Nuclear Power Plant for Efficiency Improvement Via Compressor Inlet Cooling: Thermoeconomic Optimization

Aerodynamic modification and optimization of intermediate pressure compressor in marine intercooled recuperated gas turbine

Analysis and prediction of gas turbine performance with evaporative cooling processes by developing a stage stacking algorithm

Part-load performance analysis of a combined cycle with intermediate recuperated gas turbine

Energy, Exergy & Environmental Analysis of a Combined Cycle with Pre-combustion CO2 Capture and N2 Injected into the Compressor of the Gas Turbine

Gas turbine efficiency and ramp rate improvement through compressed air injection

Combustion stage configurations for intercooled regenerative reheat gas turbine systems

Ecological Function Analysis and Optimization of a Recompression S-CO2 Cycle for Gas Turbine Waste Heat Recovery

A triple cascade gas turbine waste heat recovery system based on supercritical CO2 Brayton cycle: Thermal analysis and optimization

Process modelling and optimization of a 250 MW IGCC system: ASU optimization and thermodynamic analysis

Thermal-Economic Comparative Analysis and Optimization of the Maisotsenko Gas Turbine Cycle under Different Configurations

Comparative Study on Different Water/steam Injection Layouts for Fuel Reduction in a Turbocompound Diesel Engine

Numerical Study on Steam Injection in a Turbocompound Diesel Engine for Waste Heat Recovery

Thermodynamic Analysis of Integrated Gasification Combined Cycle Integrated with Organic Rankine Cycle for Waste Heat Utilization

Influence of Wet Compression on Operating Performance and Exhausts of Turbojet Engine