Abstract:The paper covers the production, analysis of the microstructure, crystallographic texture and deformation mechanisms of the ultrafine-grained (UFG) Zn–1%Mg–1%Fe zinc alloy demonstrating unique physical and mechanical properties compared to its coarse-crystalline analogs. The zinc alloy with improved mechanical properties was developed in two stages. At the first stage, based on the analysis of literature data, an alloy with the following chemical composition was cast: Zn–1%Mg–1%Fe. Then, the alloy was subjected to high-pressure torsion (HPT) to improve mechanical properties due to grain structure refinement and implementation of dynamic strain aging. The conducted mechanical tensile tests of the samples and assessment of the alloy hardness showed that HPT treatment leads to an increase in its tensile strength to 415MPa, an increase in hardness to 144HV, and an increase in ductility to 82%. The obtained mechanical characteristics demonstrate the suitability of using the developed alloy in medicine as some implants (stents) requiring high applied loads. To explain the reasons for the improvement of the mechanical properties of this alloy, the authors carried out comprehensive tests using microscopy and X-ray diffraction analysis. The microstructure analysis showed that during the formation of the ultrafine-grained structure, a phase transition is implemented according to the following scheme: Zneutectic + Mg2Zn11eutectic + FeZn13 → Znphase + Mg2Zn11phase + MgZn2particles + Znparticles. It was found that as a result of high pressure torsion in the main phases (Zn, Mg2Zn11), the grain structure is refined, the density of introduced defects increases, and a developed crystallographic texture consisting of basic, pyramidal, prismatic, and twin texture components is formed. The study showed that the resistance of pyramidal, prismatic and twin texture components at the initial stages of high-pressure torsion determines the level and anisotropy of the strength properties of this alloy. The relationship between the discovered structural features of the produced alloy and its unique mechanical properties is discussed.

Development of Gradient Concentrated Single-Phase Fine Mg-Zn Particles and Effect on Structure and Mechanical Properties

Mechanical Properties and Deformation Mechanism of Mg-Al-Zn Alloy with Gradient Microstructure in Grain Size and Orientation

Synergistic effect of gradient Zn content and multiscale particles on the mechanical properties of Al–Zn–Mg–Cu alloys with coupling distribution of coarse–fine grains

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Effect of Zn Concentration on the Microstructures and Mechanical Properties of Extruded Mg–7Y–4Gd–0.4Zr Alloys

Microstructure Characterization and Mechanical Properties of a Zn and Rare Earth Modified Mg Alloy

Influence of Solidification Conditions on Mechanical Properties of Mg-10gd-3y-0.5zr Magnesium Alloy

Microstructure and mechanical properties of Mg-Gd-Zn-Zr alloy after hot extrusion

Effect of High Mn Content on Development of Ultra-Fine Grain Extruded Magnesium Alloy

Microstructures and Mechanical Properties of Mg-10Gd-3Y-2Zn-0.5Zr Alloy

Microstructure, crystallographic texture and mechanical properties of the Zn–1%Mg–1%Fe alloy subjected to severe plastic deformation

Microstructural Evolution and Mechanical Properties of Mg-5y-5gd-Xnd-0.5zr Magnesium Alloys at Different States

High Performance Mg Alloy with Designed Microstructure and Phases

Enhancing the mechanical properties of Mg-Zn-Al-Cu-Mn alloy via MgCO3 inoculation treatment: Experimental studies and first-principles calculations

Excellent mechanical properties of an ultrafine-grained quasicrystalline strengthened magnesium alloy with multi-modal microstructure

Superplastic Behavior and Microstructure Evolution of a Fine-Grained Mg-Nd-Zn-Zr Alloy Processed by Hot Extrusion

Effect of twin assisted precipitation on the microstructure and mechanical properties of gradient structure Mg-Gd-Zn-Zr alloy

Microstructure, Tensile Properties and Work Hardening Behavior of an Extruded Mg–Zn–Ca–Mn Magnesium Alloy

Microstructure and Mechanical Properties of Mg–3.0Y–2.5Nd–1.0Gd–x Zn–0.5Zr Alloys Produced by Metallic and Sand Mold Casting

Excellent isotropic mechanical properties of directed energy deposited Mg-Gd-Y-Zr alloys via establishing homogeneous equiaxed grains embedded with dispersed nano-precipitation