Abstract:Following the nuclear disaster at Fukushima in Japan in 2011, there is a growing search for novel cladding materials that can displace Zirconium in light water reactors. In this paper, niobium (Nb), titanium (Ti), vanadium (Va) and Inconel-600 alloy are selected as possible innovative cladding materials that have high melting points and resist corrosion. MCNPX code was used to simulate these cladding materials in a standard pressurized water reactor assembly. The impact of these materials on the reactor safety aspects was discussed in terms of the depletion calculations at the unit cell and assembly levels. The included reactor safety aspects in this work are effective multiplication factor (K eff ), cycle length, relative fission power, reactivity coefficients, reactivity worth, fission products and actinides, neutron spectrum, spectral index, radial power distribution and peaking factor. For each proposed cladding material, the study focused on determining the required thickness (at constant enrichment) and evaluating the suitable enrichment (at constant cladding thickness) to obtain the same cycle length of zirconium. The simulation depicted that the lowest decrease of cycle length was observed for niobium which contributed to reducing the Zirconium cycle length by 15%. Meanwhile, the high absorbing cladding materials such as Ti, Va and Inconel-600 reduced the Zirconium cycle length by 29%, 32% and 40%, respectively. Enhanced negativity of fuel temperature coefficient (FTC), moderator temperature coefficient (MTC) and void reactivity coefficient are noticed for Ti, Va, and Inconel-600 at the BOL. On the other hand, Zr and Nb provide the most negativity of reactivity coefficients at the MOL and EOL owing to the low inventory of Pu-239 and fission products. The control rod worth values of Zr and Nb are larger than those of Ti, Va and Inconel-600 throughout the fuel depletion thanks to the softening of neutron spectrum in the case of Zr and Nb. In terms of minimizing the radioactive waste, Nb offers the second lowest inventory of fission products and actinides after zirconium. Finally, the peaking factors for Inconel-600, Va and Ti are slightly higher than those for Zr and Nb. As a consequence, the power distribution is more controllable in the cases of Zr and Nb.

Nitride fuel for Gen IV nuclear power systems

Physical aspects for involvement of thermonuclear reactors into nuclear power systems

Neutron radiation characteristics of the IVth generation reactor spent fuel

A fuel for generation IV nuclear energy system: Isotopic composition and radiation characteristics

Comparison of uranium plutonium nitride (U‐Pu‐N) and thorium nitride (Th‐N) fuel for 500 MWth gas‐cooled fast reactor (GFR) long life without refueling

The main problems of transmutation of actinides and long-lived fission products from NPP spent fuel

Possibility assessment for production of non-traditional nuclear fuel in thorium blanket of hybrid thermonuclear reactor

Particle emission from irradiated VVER-1200 fuel with Am burnable absorber

The possibility of utilizing novel cladding materials instead of zirconium in light water reactors

Finely Divided Metal as Nuclear Reactor Fuel

Neutronic Analysis of Thorium Nitride (Th, U233)N Fuel for 500MWth Gas Cooled Fast Reactor (GFR) Long Life without Refueling

Simulation of uranium mononitride spent fuel: A thermodynamic approach

Renewability and sustainability aspects of nuclear energy

Potentials in "nonproliferating" nuclear fuel: Design and implications on a PWR fuel cycle

Options for Managing Spent TRi-structural ISOtropic Nuclear Fuel

Investigating the possibility of using a mixture of thorium with different fissile materials as a fuel in TRISO particles for the PBMR-400 reactor

STUDY ON CRITICALITY AND NEUTRONIC SAFETY PARAMETERS OF NUSCALE FUEL ASSEMBLY

Current state and prospect on the development of advanced nuclear fuel system materials: A review

Theoretical assessment of boron incorporation in nickel ferrite under conditions of operating nuclear pressurized water reactors (PWRs)

A novel approach on designing ultrahigh burnup metallic TWR fuels: Upsetting the current technological limits

Fueling RPS with medium and medium heavy metal isotopes from fresh spent nuclear fuel of LWR