Abstract:Abstract For disposal of the research reactor of the Technical University Munich FRM II a new transport and storage cask design was under approval assessment by the German authorities on the basis of International Atomic Energy Agency (IAEA) requirements. The cask body is made of ductile cast iron and closed by two bolted lid systems with metal seals. The material of the lids is stainless steel. On each end of the cask the wood-filled impact limiters are installed to reduce impact loads to the cask under drop test conditions. In the cavity of the cask a basket for five spent fuel elements is arranged. This design has been assessed by the Bundesanstalt für Materialforschung und -prüfung (BAM) in view to the mechanical and thermal safety analyses, the activity release approaches, and subjects of quality assurance and surveillance for manufacturing and operation of the package. For the mechanical safety analyses of the package a combination of experimental testing and analytical/numerical calculations were applied. In total, four drop tests were carried out at the BAM large drop test facility. Two tests were carried out as a full IAEA drop test sequence consisting of a 9m drop test onto an unyielding target and a 1m puncture bar drop test. The other two drop tests were performed as single 9m drop tests and completed by additional analyses for considering the effects of an IAEA drop test sequence. The main objectives of the drop tests were the investigation of the integrity of the package and its safety against release of radioactive material as well as the test of the fastening system of the impact limiters. Furthermore, the acceleration and strain signals measured during the tests were used for the verification of finite-element (FE) models applied in the safety analysis of the package design. The FE models include the cask body, the lid system, the inventory and the impact limiters with the fastening system. In this context special attention was paid to the modeling of the encapsulated wood-filled impact limiters. Additional calculations by using the verified numerical model were done to investigate e.g. the brittle fracture of the cask body made of ductile cask iron within the package design approval procedure. The thermal safety assessment was based on analytical energy balance calculations and FE analyses. As an additional point of evaluation in frame of approval procedure, the effect of possible impact limiter burning under accident conditions of transport was considered by the applicant and assessed by BAM. This paper describes the package design assessment from the point of view of the competent authority BAM including the applied assessment strategy, the conducted drop tests and the additional calculations by using numerical and analytical methods.

Investigations on potential methods for the long-term monitoring of the state of fuel elements in dry storage casks

Spent fuel nondestructive assay integrated characterization from active neutron, passive neutron, and passive gamma

Design and Analysis of an Internal Remote Monitoring System for Spent Nuclear Fuel Stored in a Dry Cask

Monitoring for Actinide Neutron Emissions From Spent Nuclear Fuel Under Extreme Gamma Fields Using Centrifugally Tensioned Metastable Fluid Detector Sensor Technology

Neutron Measurements and Monte Carlo Simulations of Spent Nuclear Fuel in Dry Cask Storage Using a New Remote Monitoring System Prototype

Monte Carlo Simulations of Spent Nuclear Fuel Dry Storage Cask Measurements with a New External Remote Monitoring System for Developing Safeguards Approaches

Verifying Spent Fuel Containers Before Deep Geological Storage with Cosmic Ray Muons

Momentum informed muon scattering tomography for monitoring spent nuclear fuels in dry storage cask

Sensitivity of the neutron multiplication factor to water ingress into a spent fuel cask

Neutron Tomography of Spent Fuel Casks

Investigations of aged metal seals for interim storage

Evaluation of the in-situ Performance of Neutron Detectors based on EJ-426 Scintillator Screens for Spent Fuel Characterization

Verification of spent nuclear fuel in sealed dry storage casks via measurements of cosmic ray muon scattering

Analysis of Spent Nuclear Fuel Imaging Using Multiple Coulomb Scattering of Cosmic Muons

Neutronic Characterization for a Pressurized Water Reactor Spent Fuel Assembly

Mechanical and Thermal Assessment by BAM of a New Package Design for the Transport of SNF From a German Research Reactor

Gamma and neutron detector performance in a MOX fuel fabrication plant environment

Simulation of Neutron Leakage Variations at Fuel Substitution in a Small Modular Reactor and Implications for Unattended Safeguards Monitoring

Methodologies for imaging a used nuclear fuel dry storage cask with cosmic ray muon computed tomography

Neutrino-based safeguards of CANDU spent fuel using superconducting detectors and the CE$ν$NS interaction

Stand-off nuclear reactor monitoring with neutron detectors for safeguards and non-proliferation applications