Abstract:Aluminium alloy 6061-T6 (AA6061-T6) shows a promising potential for cryogenic structural applications. This alloy exhibits remarkable monotonic tensile properties at low temperatures. However, there is a limited number of studies on the cryogenic deformation behaviour. In this study, both monotonic and cyclic loading were conducted, and various microstructure characterisation techniques were performed to understand influence of cryogenic temperatures on microstructure evolution and deformation behaviour of this alloy. At cryogenic temperatures, the aluminium alloy exhibited superior mechanical properties over those at room temperature. Yield stress, UTS and elongation at failure increased by 18%, 33%, and 53% at 77 K compared to those at room temperature. Such increase in mechanical properties was attributed by the stronger resistance to dislocation movement due to the reduced thermal assistance. Work hardening rate also increased as dynamic recovery was suppressed at lower temperatures. As a result, a high density of dislocations was evenly distributed within grain interior and led to a homogeneous deformation. The test temperature appeared to have a significant influence on fatigue performance; maximum stress response increased by 23% at 108 K with respect to those at room temperature. During cyclic loading, a high number of dislocations was generated to accommodate prescribed strain because of the resistance to dislocation movement including the pinning of dislocations by β'' precipitates which are known to be sheared at room temperature. Thus, the alloy exhibited an enhanced cyclic hardening behaviour without a noticeable cyclic softening phase. Fatigue life improved by 143% at 108 K with respect to that at room temperature as the homogeneous deformation prohibited localised slip activity and delayed formation of slip bands which act as crack initiation sites. Moreover, the initiation and propagation of secondary cracks at 108 K retarded the propagation of main crack to improve fatigue life. Graphical

Cryogenic rejuvenation of Al-based amorphous-nanocrystalline alloys

Effect of Deep Cryogenic Treatment on the Artificial Aging Behavior of 6082 Aluminum Alloy

Structure and phase transformations of amorphous-nanocrystalline Al-based alloy

Effects of cryogenic treatments on phase transformations, microstructure and mechanical properties of near βTi alloy

The effect of changes in Al-based amorphous phase structure on structure forming upon crystallization

Effect of heat treatment on the microstructure and mechanical properties of cryogenic rolling 2195 Al–Cu–Li alloy

Effect of deep cryogenic treatment on the microstructure and mechanical properties of Al–Cu–Mg–Ag alloy

Investigation of the impacts of artificial ageing, re-ageing and cryogenic cycles on multiplex second phase precipitation and life-time prediction in 7075 alloy

Cryogenic thermal cycling rejuvenation in metallic glasses: Structural and mechanical assessment

Cryogenic Deformation Behaviour of Aluminium Alloy 6061-T6

Examining The Phase Formation of Aging and Shallow Cryogenic Process Applied to Aluminum Alloys with Thermal Analysis

Improving the wear performance of a commercial Vit 1 amorphous alloy by a cryogenic cycling treatment

Effect of Cycle Index on the Microstructural Evolution of Alumina Particles Reinforced Aluminum Composites Treated by Cryogenic Treatment

Effect of Cryorolling and Ageing on the Microstructure and Mechanical Properties of Al 7085 Alloy

Achieving synergistic improvement of wear and mechanical properties in Ti–6Al–4V alloy by multiple cryogenic treatment

Tailoring rejuvenation behavior of Zr-based metallic glass upon deep cryogenic cycling treatment

Effect of Cryogenic Treatment on Microstructure and Mechanical Properties of Al0.6CrFe2Ni2 Dual-Phase High-Entropy Alloy

The effect of cryogenic thermal cycling on aging, rejuvenation, and mechanical properties of metallic glasses

Crystallization behavior and corrosion resistance of Al86Ni10Zr4 amorphous alloy under different annealing treatment conditions

Grain Structure and Intermetallic Evolution of Nb-containing FeCrAl Alloy Treated by Cryogenic Laser Quenching

Microstructures and Cryogenic Mechanical Properties of Spray Deposited 2195 Al–Cu–Li Alloy with Different Heat Treatments