Abstract:Context: Powder metallurgy uses metallic and/or non-metallic powders that, through mixing, compacting, and sintering operations, allow obtaining large series of products. In austenitic stainless steels, Cr23C6-type carbides can precipitate at temperatures between 450 and 950 °C. When this occurs, the steel is susceptible to being attacked at its grain boundaries by a phenomenon called sensitization. Titanium is added as a ‘stabilizer’ because it has a greater affinity with carbon for the formation of species at a temperature of approximately 900 oC, and, during cooling, it consumes the carbon forming MC-type carbides, inhibiting the precipitation of Cr23C6. Method: The composition and morphology of the powders were characterized, leading to the formulation of an alloy matrix consisting of a mixture of AISI 316 steel powders of two different particle-size distributions in a proportion that produced the highest density and the lowest porosity in the sintered material. Titanium was added at two levels (0,4 and 1,0 wt%), and sintering was carried out with nitrogen. The corrosion rate was determined by potentiodynamic polarization. Vickers hardness and pin-on-disk wear tests were performed. The stages were complemented with a microstructural analysis. Results: The addition of 0,4 wt% of titanium decreased the steel’s rate of corrosion, albeit in the absence of passivation. The microstructure consists of austenite, ferrite, and TiC precipitates. The addition of 1,0 wt%Ti showed an increase in the corrosion rate, with a microstructure containing austenite, ferrite, TiC carbides, and the Laves ɳ-Fe2Ti phase. Conclusions: The results were compared against thermodynamic simulations in the Thermo-Calc software, which were consistent with the microstructural analysis, showing the phenomena of stabilization as well as the precipitation of intermetallic phases and highlighting the importance of establishing strict controls in the formulation of powder metallurgical alloys due to the transformations that can take place due to the effect of the thermal cycles of the process.

Principles of Chemical Metallurgy of Titanium Microalloyed Steel

Titanium microalloying of steel: A review of its effects on processing, microstructure and mechanical properties

Additive manufacturing of titanium alloys with enhanced strength and uniform ductility via multi-element alloying

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Microstructure Design and Its Effect on Mechanical Properties in Gamma Titanium Aluminides

The important role of titanium microalloying in refining austenite grain of heavy‐duty H‐beam steel during rough rolling produced by a new technology

Microstructure Evolution Behavior of Titanium Microalloyed Steel during Heat Treatment

Study Of the Effect of Titanium Additions on The Mechanical and Corrosion Properties of AISI 316 Powder Metallurgical Steel

Versatility of trace nano-TiC–TiB2 in collaborative control of solidification-rolling-welding microstructural evolution in Al–Mg–Si alloy for enhanced properties

Effect of Micro-Alloyed Ti on Inclusions Modification

Microstructure and Properties of a Low Carbon Ti-V Microalloyed Steel

Microstructure and Properties of Ti Microalloyed Automobile Frame Steel 510L

Metastable microstructure evolution and grain refinement in a Low-Ta containing γ-TiAl alloy through heat treatment

Effect of Ti content on microstructures and mechanical properties of cast Al-2Li-2Cu-0.5Mg alloy

Role of Microalloying Elements on Recrystallization Kinetics of Cold-Rolled High Strength Low Alloy Steels

Additive manufacturing of fine-grain fully lamellar titanium aluminide alloys

Application of alloying for enhancing the corrosion resistance of titanium alloys: A review

Thermodynamic Research on the Precipitation of Ti2O3, TiN and TiC in Continuous Casting of Titanium Microalloyed Steel

A thermodynamic model of the titanium distribution behaviour between slag and molten steel during LF refining process: description and application

Optimization of Processing Parameters and Microstructure Evolution of (TiB+La 2 O 3 )/Ti6Al4V Manufactured by Laser Melting Deposition

Microstructure evolution and strengthening mechanism of high-performance powder metallurgy TA15 titanium alloy by hot rolling