Abstract:Wind energy is the world’s fastest growing source of electricity production; if this trend is to continue, sites that are plentiful in terms of wind velocity must be efficiently utilized. Many such sites are located in cold, wet regions such as the Swiss Alps, the Scandinavian coastline, and many areas of China and North America, where the predicted power curves can be of low accuracy, and the performance often deviates significantly from the expected performance. There are often prolonged shutdown and inefficient heating cycles, both of which may be unnecessary. Thus, further understanding of the effects of ice formation on wind turbine blades is required. Experimental and computational studies are undertaken to examine the effects of ice formation on wind turbine performance. The experiments are conducted on a dynamically scaled model in the wind turbine test facility at ETH Zurich. The central element of the facility is a water towing tank that enables full-scale nondimensional parameters to be more closely matched on a subscale model than in a wind tunnel. A novel technique is developed to yield accurate measurements of wind turbine performance, incorporating the use of a torquemeter with a series of systematic measurements. These measurements are complemented by predictions obtained using a commercial Reynolds-Averaged Navier–Stokes computational fluid dynamics code. The measured and predicted results show that icing typical of that found at the Guetsch Alpine Test Site (2330 m altitude) can reduce the power coefficient by up to 22% and the annual energy production (AEP) by up to 2%. Icing in the blade tip region, 95–100% blade span, has the most pronounced effect on the wind turbine’s performance. For wind turbines in more extreme icing conditions typical of those in Bern Jura, for example, icing can result in up to 17% losses in AEP. Icing at high altitude sites does not cause significant AEP losses, whereas icing at lower altitude sites can have a significant impact on AEP. Thus, the classification of icing is a key to the further development of prediction tools. It would be advantageous to tailor blade heating for prevention of ice buildup on the blade’s tip region. An “extreme” icing predictive tool for the project development of wind farms in regions that are highly susceptible to icing would be beneficial to wind energy developers.

Uncertainty Quantification of Aerodynamic Icing Losses in Wind Turbine With Polynomial Chaos Expansion

Performance Impact of Flow and Geometric Variations for a Turbine Blade Using an Adaptive NIPC Method

Quantification Of Performance Uncertainty For A Transonic Compressor Rotor Using An Adaptive Nipc Method

Uncertainty Quantification for Airfoil Icing using Polynomial Chaos Expansions

Performance Impact of Uncertain Variations of Inlet Flow for Axial Compressor Blades

Impact of Inlet Flow Angle Variation on the Performance of a Transonic Compressor Blade Using NIPC

Statistical Evaluation of Performance Impact of Flow Variations for a Transonic Compressor Rotor Blade

Numerical simulations of ice accretion on wind turbine blades: are performance losses due to ice shape or surface roughness?

Data-integrated uncertainty quantification for the performance prediction of iced airfoils

Multiphysics Based Numerical Study of Atmospheric Ice Accretion on a Full Scale Horizontal Axis Wind Turbine Blade

Numerical simulation of icing effect on aerodynamic characteristics of a wind turbine blade

Numerical analysis of blade icing influence on the dynamic response of an integrated offshore wind turbine

Study on the Icing Characteristics of Typical Wind Turbine

Influence of Surface Roughness Modeling on the Aerodynamics of an Iced Wind Turbine S809 Airfoil

A Review on the Estimation of Power Loss Due to Icing in Wind Turbines

Aerodynamic shape optimization of wind turbine blades for minimizing power production losses due to icing

Numerical Simulation of Icing on Nrel 5-MW Reference Offshore Wind Turbine Blades Under Different Icing Conditions

A Survey of the Quasi-3D Modeling of Wind Turbine Icing

Prediction of ice accretion and anti-icing heating power on wind turbine blades using standard commercial software

Numerical Calculation Method of Spanwise Icing Characteristics and Performance Loss of Three-Dimensional Vertical Axis Wind Turbine Blades

The Impact of Ice Formation on Wind Turbine Performance and Aerodynamics