Abstract:Abstract. There has been a substantial growth in the wind energy power capacity worldwide, and icing difficulties have been encountered in cold climate locations. Rotor blade icing has been recognized as an issue, and solutions to mitigate accretion effects have been identified. Wind turbines are adapting helicopter rotor and propeller ice protection approaches to reduce aerodynamic performance degradation related to ice formation. Electro-thermal heating is one of the main technologies used to protect rotors from ice accretion, and it is one of the main technologies being considered to protect wind turbines. In this research, the design process required to develop an ice protection system for wind turbines is discussed. The design approach relies on modeling and experimental testing. Electro-thermal heater system testing was conducted at the Adverse Environment Rotor Test Stand at Penn State, where wind turbine representative airfoils protected with electro-thermal deicing were tested at representative centrifugal loads and flow speeds. The wind turbine sections tested were half-scale models of the 80 % span region of a generic 1.5 MW wind turbine blade. The icing cloud impact velocity was matched to that of a 1.5 MW wind turbine at full power production. Ice accretion modeling was performed to provide an initial estimate of the power density required to de-bond accreted ice at a set of icing conditions. Varying icing conditions were considered at −8 ∘C with liquid water contents of the cloud varying from 0.2 to 0.9 g/m3 and water droplets from 20 μm median volumetric diameter to 35 μm. Then, ice accretion thickness gradients along the span of the rotor blade for the icing conditions were collected experimentally. Given a pre-determined maximum power allocated for the deicing system, heating the entire blade was not possible. Heating zones were introduced along the span and the chord of the blade to provide the required power density needed to remove the accreted ice. The heating sequence for the zones started at the tip of the blade, to allow de-bonded ice to shed off along the span of the rotor blade. The continuity of the accreted ice along the blade span means that when using a portioned heating zone, ice could de-bond over that specific zone, but the ice formation could remain attached cohesively as it is connected to the ice on the adjacent inboard zone. To prevent such cohesive retention of de-bonded ice sections, the research determined the minimum ice thickness required to shed the accreted ice mass with the given amount of power availability. The experimentally determined minimum ice thickness for the varying types of ice accreted creates sufficient tensile forces due to centrifugal loads to break the cohesive ice forces between two adjacent heating zones. The experimental data were critical in the design of a time sequence controller that allows consecutive deicing of heating zones along the span of the wind turbine blade. Based on the experimental and modeling efforts, deicing a representative 1.5 MW wind turbine with a 100 kW power allocation required four sections along the blade span, with each heater section covering 17.8 % span and delivering a 2.48 W/in.2 (0.385 W/cm2) power density.

Prediction of ice accretion and anti-icing heating power on wind turbine blades using standard commercial software

Wind Tunnel Test and Numerical Computation on Ice Accretion on Blade Airfoil for Straight-bladed VAWT

Numerical Estimation of Anti-icing Heating Power for NREL 5MW Wind Turbine Blades in Cold Climate

2D Numerical Simulation of a Wind Turbine De-Icing System, Using Cycled Heating

SIMULATION BY MEANS FINITE ELEMENTS OF A PREVENTIVE ANTI-ICING SYSTEM FOR WIND TURBINE BLADES

Multiphysics Based Numerical Study of Atmospheric Ice Accretion on a Full Scale Horizontal Axis Wind Turbine Blade

A novel method for robust and efficient prediction of ice shedding from rotorcraft blades

Numerical simulation of icing effect on aerodynamic characteristics of a wind turbine blade

Influence of Surface Roughness Modeling on the Aerodynamics of an Iced Wind Turbine S809 Airfoil

Numerical simulation for in-cloud icing of three-dimensional wind turbine blades

Design procedures and experimental verification of an electro-thermal deicing system for wind turbines

Monitoring Ice Accumulation and Active De-icing Control of Wind Turbine Blades

Warm-Air Intermittent De-Icing System for Wind Turbines

A numerical investigation of the effects of ice accretion on the aerodynamic and structural behavior of offshore wind turbine blade

A Combined Data-Driven and Simulation Approach for Wind Turbine Blade Icing Prediction in Cold Regions

Simulation of Rime Ice Accretion on Wind Turbine Blade

Numerical analysis of blade icing influence on the dynamic response of an integrated offshore wind turbine

Numerical simulations of ice accretion on wind turbine blades: are performance losses due to ice shape or surface roughness?

Modelling and empirical development of an anti/de-icing approach for wind turbine blades through superposition of different types of vibration

A frost ice formation method of horizontal axis wind turbine blade based on polynomial fitting

Uncertainty Quantification of Aerodynamic Icing Losses in Wind Turbine With Polynomial Chaos Expansion