Abstract:Highly efficient and stable, rigid and flexible p‐i‐n perovskite solar cells are developed by incorporating a 2‐(acetyloxy)‐N,N,N‐trimethylethanium chloride additive into the lead iodide precursor solution to prepare a porous PbI2 layer. The good diffusion of the organic ammonium salt results in flat and dense perovskite film with large particle size, which achieves high power conversion efficienciesPCE of 23.40% (rigid) and 21.10% (flexible) with excellent ambient and mechanical stability. Flexible perovskite solar cells (FPSCs) are attracting widespread research and attention for their benefits as the next‐generation wearable electronic products. However, there are still many challenges in the quest to achieve dense, pinhole‐free, high crystal quality, low defect, and stable perovskite films, which limit further improvement in the efficiency and stability of FPSCs. Herein, a novel technique for the incorporation of quaternary ammonium halide (QAH) additives to prepare fluffy porous lead iodide layers by using a two‐step sequential deposition method, is reported. Benefiting from the good diffusion of organic amine salts on porous PbI2 layers, flat and dense perovskite films are produced with large particle sizes, few defects, and high crystal quality. Finally, the champion rigid and flexible p‐i‐n PSCs with the 2‐(acetyloxy)‐N,N,N‐trimethylethanium chloride (AtaCl) additive achieves exciting power conversion efficiencies (PCE) of 23.40% and 21.10%, respectively. The device with the AtaCl additive retains over 90% of its original PCE under ambient conditions (40 ± 5% relative humidity (RH)) over 1000 h of aging without encapsulation. In addition, the flexible device with the AtaCl additive shows excellent stability under mechanical bending conditions, retaining ≈85% of its original PCE after 10 000 cycles (bending radius = 5 mm).

Record‐Efficiency Flexible Perovskite Solar Cells Enabled by Multifunctional Organic Ions Interface Passivation

Record Efficiency Stable Flexible Perovskite Solar Cell Using Effective Additive Assistant Strategy

SnO2 Surface Modification and Perovskite Buried Interface Passivation by 2,5‐Furandicarboxylic Acid for Flexible Perovskite Solar Cells

Fapbi(3) Flexible Solar Cells With A Record Efficiency Of 19.38% Fabricated In Air Via Ligand And Additive Synergetic Process

High‐Performance Flexible Perovskite Solar Cells via Precise Control of Electron Transport Layer

Highest‐Efficiency Flexible Perovskite Solar Module by Interface Engineering for Efficient Charge‐Transfer

Porous Lead Iodide Layer Promotes Organic Amine Salt Diffusion to Achieve High Performance p‐i‐n Flexible Perovskite Solar Cells

Dual-Interface-Reinforced Flexible Perovskite Solar Cells for Enhanced Performance and Mechanical Reliability

Buried Interface Optimization for Flexible Perovskite Solar Cells with High Efficiency and Mechanical Stability

Stable 25 % Efficiency Inorganic Perovskite/Organic Tandem Solar Cells Enabled by Methoxy-free D-A-D'-A-D Interconnecting Layer

Halide Substituted Ammonium Salt Optimized Buried Interface for Efficient and Stable Flexible Perovskite Solar Cells

Creating a Dual‐Functional 2D Perovskite Layer at the Interface to Enhance the Performance of Flexible Perovskite Solar Cells

A novel 2D perovskite as surface "patches" for efficient flexible perovskite solar cells

Organic‐Hydrochloride‐Modified ZnO Electron Transport Layer for Efficient Defect Passivation and Stress Release in Rigid and Flexible all Inorganic Perovskite Solar Cells

Concurrent Top and Buried Surface Optimization for Flexible Perovskite Solar Cells with High Efficiency and Stability

High-Performance Perovskite Solar Cells with Low Open-Circuit Voltage Loss and Excellent Stability after p-F-PEAI Posttreatment

Enhanced photovoltaic performance of SnO2 based flexible perovskite solar cells via introducing interfacial dipolar layer and defect passivation

Dual Role of Rapid Transport and Efficient Passivation in Inverted Methylammonium‐Free Perovskite Solar Cells Utilizing a Self‐Assembled Porous Insulating Layer

Selective Chemical Etching to Remove 0D Cs4Pb(IBr)6 from Mixed‐Dimensional Perovskite Surface Achieving High Efficiency Flexible All‐Inorganic Perovskite Solar Cells with Superior Mechanical Durability

Efficient Perovskite Solar Cells by Employing Triphenylamine-Functionalized Azadipyrromethene Dyes as Dopant-Free Hole-Transporting Materials and Bidentate Surface Passivating Agents