Abstract:Wear due to sliding is an inevitable problem in many engineering applications. Protective surface coating is usually used to mitigate this problem. The development in this field is continuous and consistent. There are many types of coatings according to their compositions and the deposition methods. One of the coatings with the most promising properties, such as the hardness, is the Diamond-Like Carbon (DLC) coating. The tribological properties of this coating generated by Plasma-Assisted Chemical Vapor Deposition (PACVD) and applied on bearing steel 52100 ASTM are not available. In this study, the wear resistance of the DLC coating applied to bearing steel 52100 ASTM, was evaluated. The coating method employed was PACVD, which is regarded as one of the most distinctive coating techniques due to the unique tribological properties imparted to the coating. The pin-on-disc tribometer was used to examine the coefficient of friction and mass losses for samples of (steel disc against steel ball) and (DLC coated disc against DLC coated ball) under constant sliding velocity and constant sliding distance with four different loads (2, 5, 10 and 20 N) that results in maximum contact pressure below and higher than the maximum shear stress of the bearing steel. The wear coefficient was calculated using Archard's equation based on the experimental results. It was found that the DLC coating may result in significant reduction, reaching 93.5%, in weight loss and 83% in COF at low contact pressure (less than the maximum shear stress). However, at high contact pressure (equals to or higher than the maximum shear stress) the weight loss and the COF for the DLC coating are higher than those of the bearing steel. This behavior indicates that the DLC coated pair may not be suitable at high loads. The wear coefficient is calculated for each testing condition and it is found to be affected by the applied load. The average wear coefficient for the DLC coating is provided which can be used with the Archared wear model to predict the wear rate within the range of the parameters used in this study.

Parametric Effect on Tribological Performance of Plasma-Sprayed Composite Coating on Bearing Steel

ANALYSIS OF THE TRIBOLOGICAL PROPERTIES OF TiN/Si3N4 NANOCOMPOSITE COATING IN SLIDING CONTACT WITH CERAMIC, STEEL, AND POLYMER COUNTERPART

Tribological Behavior of Atmospheric Plasma-Sprayed Cu-Ni Coatings

Analysis of tribological behavior, pin temperature, and surface roughness of a brake pad material with nano coating

Unveiling the influence of nickel on the erosion and the tribological performance of AlSi-based abradable coatings

Synergetic influence of TiCnp and graphite particles on tribological performance of Cu based composites prepared by flake powder metallurgy

Wear Performance Evaluation of Polymer Overlays on Engine Bearings

Effect of Heat Treatment on the Microstructure, Mechanical Property and Tribological Property of Plasma-Sprayed High Temperature Lubricating Composite Coating from Nanostructured Powder

A Study of Parameters Affecting Wear Resistance of Alumina and Yttria Stabilized Zirconia Composite Coatings on Al-6061 Substrate

Parameter optimization for enhancing tribological properties of sol–gel alumina and aluminum silicate-coated aluminum alloy: Grey–Taguchi method

Effects of Ni-5 wt% Al/Bi2O3 addition and heat treatment on mechanical and tribological properties of atmospheric plasma sprayed Al2O3 coating

Effect of Heat‐Treatment and NiB–TiO2 Composite Coating on the Tribological Performance of AISI P20 Steel

Effect of SiC Weight Percentage on Tribological Characteristics of Al7075/SiC Composites

Plasma Spraying NiCoCrAlY-Cr2O3-AgMo Coatings: Fabrication and Tribological Mechanisms

Effects Of Wear Conditions On Tribological Properties Of Tib2-Tic/Ni Composite Coating By Plasma Cladding

Tribological Behavior of Various Plasma-Sprayed Ceramic Coatings

The effect of diamond like carbon coating on the wear resistance at dry sliding conditions

Tribological investigation into nickel-coated graphite polytetrafluoroethylene composites

Development of Tribologically Optimized Surface Coatings with Micro and Nano Particles

Tribological Performance of a Composite Cold Spray for Coated Bores

Tribological properties of PEEK-based composite coating prepared by thermal spraying