Abstract:Combined use of thermal analysis techniques can realize complementarity of different characterization methods. Comprehensive thermal analysis with both thermogravimetric analysis and differential thermal analysis (TG/DTA) can measure not only mass change of a sample but also its temperature change during programmed heating-induced reaction or phase transition processes, thereby obtaining multiaspect thermal information of the material such as dehydration, structural decomposition, phase change and thermal stability. This study proposes and develops a MEMS chip-based TG/DTA microsystem that integrates both programmed heating and detecting elements into a TG chip and a DTA chip to enable the microinstrument performing TG/DTA joint characterization under microscope observation. The TG chip contains a self-heating resonant microcantilever to measure heating-induced mass change of a sample and the DTA chip is with a microheater and a temperature-detecting thermopile integrated on a suspended thermal-insulating diaphragm. Only nanogram and microgram-level samples are needed for the TG and DTA chips, thereby achieving safe measurement to energetic materials such as strong oxidants. The chip-based microinstrument surpasses the state-of-the-art commercial TG/DTA instruments that have, in the long term, suffered from large sample-amount (milligram level) requirements and have been unable to measure energetic materials. Compared with commercial instruments, the chip-based microinstrument is advantageous given its more accurate analysis, much higher heating rate, much smaller instrument volume and much lower power consumption, etc. The microinstrument has been fabricated by using wafer-level MEMS techniques. Testing results show that the mass-detection sensitivity of the TG-chip is as high as 0.45 Hz/pg in air and the temperature sensitivity of the DTA chip achieves 2.9 mV/K under the high heating rate of 25 °C/s. The strong oxidant of KMnO4 is analyzed with the TG/DTA joint characterization under microscopic observation. At the same time as microscope observation of the thermal decomposition phenomena, two-step thermal decomposition process of KMnO4 is identified and the thermal decomposition temperatures are obtained. The TG/DTA microinstrument is promising to be applied for study of various materials.

NON-DESTRUCTIVE TESTING METHOD OF MATERIALS AND PRODUCTS THERMOPHYSICAL CHARACTERISTICS USING MICROWAVE HEATING IN PRODUCTS REAL OPERATING CONDITIONS

Design and Testing of a Micro Thermal Sensor for Non-Contact Surface Defect Detection.

Design and Testing of a Micro-thermal Sensor Probe for Nondestructive Detection of Defects on a Flat Surface

Modern Trends in the Application of Thermoelectric Method in Nondestructive Testing (Review)

Thermal Conductivity Measurement System for Functional and Structural Products

Features and results of assessment the thermal conductivity of building materials and products by the active method of thermal non-destructive testing

Measurement of the Thermal Diffusivity of Optical Materials and Products by a New Thermographic Express Method That Does Not Require Cutting Samples Out of the Bulk

Thermal Nondestructive Testing of Composite and Metal Parts Manufactured by Additive Technologies

Temperature Measurement Methods in Microwave Heating Technologies

An On-Line System for High Temperature Dielectric Property Measurement of Microwave-Assisted Sintering Materials

Nondestructive Testing Methods for Studying the Diffusion Coefficient in thin Porous Materials: Comparison of Metrological Characteristics

THERMOELECTRIC MONITORING OF THERMAL RESISTANCE IN ELECTRONIC SYSTEMS

The use of infrared thermography for materials characterization

Theoretical introduction to express way of the complex determination of the thermophysical parameters of metals

Exposure of Food Samples to Pulsed Microwave Radiation to Increase their Microbiological Safety and Shelf Life

Non-contact methods for thermal properties measurement

Experimental investigation on the measurement performance of high-speed ultrasonic wave thermometry in ambient- and high-temperature environments

Chip-Based MEMS Platform for Thermogravimetric/Differential Thermal Analysis (TG/DTA) Joint Characterization of Materials

Simultaneous Measurement of Thermal Conductivity and Volumetric Heat Capacity of Thermal Interface Materials Using Thermoreflectance

Optical Detection of Phase Transformations in Steels: An Innovative Method for Time-Efficient Material Characterization During Tailored Thermo-mechanical Processing of a Press Hardening Steel

Automated system for measuring thermal conductivity of solid materials