Abstract:A new and promising approach to the reduction of greenhouse gas emissions is the use of improved lightweight constructions based on multi-material systems comprising sheet metal with local carbon fibre reinforced plastic (CFRP) reinforcements. The CFRP is used to reinforce highly stressed areas and can be aligned to specific load cases. The locally restricted application of CFRP means that the material costs can be effectively reduced by comparison to parts made entirely of CFRP on account of the expensive production process requiring the use of an autoclave. These parts are thus only used in high-priced products. The production of hybrid CFRP steel structures in a mass production process calls for an efficient production technology. Current research work within the scope of a collaborative research project running at the University of Paderborn is concentrating on the development of manufacturing processes for the efficient production of automotive structural components made up of sheet metal blanks with local CFRP patches. The project is focusing especially on basic research into the production of industrial components. The aim of the investigation is to create an efficient and controlled process for producing CFRP reinforced steel structures from semi-finished hybrid steel-CFRP material. This includes tool concepts and an appropriate process design to permit short process times. The basis of an efficient process design is an in-depth knowledge of the material behaviour, and hence a thorough characterisation was performed. Material parameters were determined for both simulation and forming. For this, monotonic tensile, shear and bending tests were conducted using both uncured prepregs and cured CFRP specimens. To achieve an accurate simulation of the forming process, a special material model for carbon fibre prepregs has been developed which also includes the anisotropic material behaviour resulting from fibre orientation, the viscoelastic behaviour caused by the matrix and the hardening effects that prevail during curing. Recent results show good qualitative agreement and will be presented in this paper. In order to control the properties of the hybrid components, four different tool concepts for the prepreg press technology have been developed and tested. The concepts are presented and the results of experimental investigations are discussed in this paper.

FILM-ADHESIVES FOR POLYMER-METAL HYBRID STRUCTURES FROM LABORATORY TO CLOSE-TO-PRODUCTION

On the strength of joints of metal-plastic composites of hot-formed steel with an AlSi coating and a thermosetting fiber reinforced compression material

Manufacturing Processes for Combined Forming of Multi-Material Structures Consisting of Sheet Metal and Local CFRP Reinforcements

Inverse Fiber Reinforced Polymer/Metal-Hybrid Laminates for Structural Lightweight Applications

Investigation of the Compound Strength of Hybrid Casting Components with Different Variations of Coated and Undercut Sheet Metal

Influence of metal surface structures on composite formation during polymer‐metal‐joining based on reactive Al/Ni multilayer foil

Lightweight Chassis Components — The Development of a Hybrid Automotive Control Arm from Design to Manufacture

Integrating interfacial bonding and coordinated deformation in steel/Al bilayers via a pin-less friction stir-assisted synchronous joining-forming approach

Process Design for Hybrid Sheet Metal Components

Influence of hollow glass microspheres on 1K epoxy structural adhesive for the automotive industry

Polymer Composite Thermoforming: Ultrasonic-Assisted Optimization for Enhanced Adhesive Performance in Automotive Interior Components

Acrylonitrile‐butadiene‐lignin thermoplastic rubber adhesive for enhanced metal‐to‐metal joining

Development and Analysis of a New Joining Method for Polymer-Metal Hybrid Structures

Investigation of the specific adhesion between polyurethane foams and thermoplastics to suited material selection in lightweight structures

Expanding Lightweight Design Potential by Hybrid Joining of Aluminum Sheets with Aluminum Casting Through Compound Sand Casting and Induction Heating

Production and Forming of Deposition‐Welded Hybrid Multimaterial Shafts

Effect of Metal Surface Topography on the Interlaminar Shear and Tensile Strength of Aluminum/Polyamide 6 Polymer-Metal-Hybrids

Sustainable design and life cycle engineering of adhesive joints for polymeric products: assessment of surface activation technologies

Textile-based surface design of thermoplastic composites for microstructural adhesion to polyurethane foams for lightweight structures

Self-Pierce Riveting: Development and Assessment for Joining Polymer—Metal Hybrid Structures in Lightweight Automotive Applications